Mitsubishi 380. Manual — part 428
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-252
INSPECTION PROCEDURE 15: Sports Mode Switch System
.
CIRCUIT OPERATION
If the select switch of the shift switch assembly is set
to the sport mode, battery positive voltage will be
applied to the A/T-ECU connector B-19 (terminal 17).
If the shift switch of the shift switch assembly is set to
"UP" or "DOWN" position, battery positive voltage
will be applied to the A/T-ECU connector B-19 (termi-
nals 8 and 9).
AC306223
A-13 (GR)
AB
CONNECTOR: A-13
1
4
7
8
2 3
5
13 14
17
15
12
16
11
10
9
6
16DB564A
COVER
AIR
CLEANER
A/T
CONTROL
UNIT
CONNECTORS: B-19, B-22
AC210068
CONNECTOR: B-110
B-110 (B)
AE
TRANSMISSION
RANGE SWITCH
1
7
2
8
3
5
9
4
10
6
10DB093A
CONNECTOR: D-14
FLOOR
WIRING
HARNESS
4
Y
2
15
ROOF
WIRING
HARNESS
D-14
10DB084A
CONNECTORS: C-214, 215
1
3 4
2
6
5
C-214
C-215
6
1
7
2
9
8
10
3
5
12
11
4
1314
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-253
.
COMMENT
When sport mode shift does not operate the cause is
probably a malfunction of the transmission inhibitor
switch circuit, shift switch assembly circuit or a defec-
tive A/T-ECU.
.
TROUBLESHOOTING HINTS (THE MOST
LIKELY CAUSES FOR THIS CASE:)
• Malfunction of the transmission inhibitor switch
• Malfunction of the shift switch assembly select
switch
• Malfunction of the shift switch assembly shift
switch (Up)
• Malfunction of the shift switch assembly shift
switch (Down)
• Damaged harness or connector
• Malfunction of the A/T-ECU system
Circuit drawings
• Refer to circuit diagrams GROUP-
• Refer to configuration diagrams GROUP-
• Refer to component locations GROUP-
DIAGNOSIS
Required Special Tool:
• MB991958: Diagnostic Tool (MUT-III Sub Assembly)
• MB991824: V.C.I.
• MB991827: MUT-III USB Cable
• MB991910: MUT-III Main Harness A
STEP 1. Using diagnostic tool MB991958, read the A/T
diagnostic trouble code.
CAUTION
To prevent damage to diagnostic tool MB991958, always
turn the ignition switch to the "LOCK" (OFF) position
before connecting or disconnecting diagnostic tool
MB991958.
(1) Connect diagnostic tool MB991958 to the data link
connector.
(2) Turn the ignition switch to the "ON" position.
(3) Check for A/T diagnostic trouble code.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is (P0705) set?
YES <(P0705)> : Refer to
: Transmission Inhibitor
Switch System (Open Circuit) or refer to
:
Transmission Inhibitor Switch System (Short Circuit).
NO : Go to Step 2.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-254
STEP 2. Using diagnostic tool MB991958, check data list
item 27: Select Switch, item 28: Shift Switch (Up), item 29:
Shift Switch (Down).
(1) Connect diagnostic tool MB991958 to the data link
connector.
(2) Turn the ignition switch to the "ON" position.
(3) Set diagnostic tool MB991958 to the data reading mode for
following items.
a. Item 27: Select Switch
b. Item 28: Shift Switch (Up)
c. Item 29: Shift Switch (Down)
NOTE: The switches above are displayed, depending on
the selector lever condition as shown in the table.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the switch operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
NO <If completely NG> : Go to Step 3.
NO <If item 28 and item 29 both are NG> : Go to Step 5.
NO <If only item 27 is NG> : Go to Step 9.
NO <If only item 28 is NG> : Go to Step 17.
NO <If only item 29 is NG> : Go to Step 22.
SELECTOR LEVER
OPERATION
DATA LIST ITEM
27
28
29
D range
OFF
OFF
OFF
Sport mode
ON
OFF
OFF
Upshift and hold the selector
lever
ON
ON
OFF
Downshift and hold the
selector lever
ON
OFF
ON
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-255
STEP 3. Check A/T-ECU connector B-19 and shift switch
assembly connector D-14 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are the connectors in good condition?
YES : Go to Step 4.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
10DB125A
COVER
AIR
CLEANER
A/T
CONTROL
UNIT
CONNECTOR: B-19
10DB093A
CONNECTOR: D-14
FLOOR
WIRING
HARNESS
4
Y
2
15
ROOF
WIRING
HARNESS
D-14
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст