Mitsubishi 380. Manual — part 83
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-329
NOTE: Also check junction block connector C-214 for loose,
corroded, or damaged terminals, or terminals pushed back in
the connector. If junction block connector C-214 is damaged,
repair or replace the damaged component(s) as described in
GROUP 00E, Harness Connector Inspection
Q: Is the wiring harness between side turn-signal lamp
(RH) connector A-35 (terminal 1) and ETACS-ECU
connector C-219 (terminal 9) in good condition?
YES : Replace the side turn-signal lamp socket (RH). Verify
that the turn-signal lamps illuminate normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the turn-signal lamps illuminate normally.
STEP 26. Check rear combination lamp (LH) connector
F-09 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Is rear combination lamp (LH) connector F-09 in good
condition?
YES : Go to Step 27.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the turn-signal lamps illuminate
normally.
STEP 27. Check the rear turn-signal lamp bulb (LH).
(1) Remove the rear turn-signal (LH) lamp bulb.
(2) Verify that the rear turn-signal lamp bulb (LH) is not
damaged or burned out.
Q: Is the rear turn-signal (LH) lamp bulb in good condition?
YES : Go to Step 28.
NO : Replace the rear turn-signal (LH) lamp bulb. Verify
that the turn-signal lamps illuminate normally.
54DB057A
CONNECTOR: C-214
HARNESS SIDE
10
1
6
14
5
12
13
4
11
7
2
3
8
9
AC305260
HARNESS SIDE
CONNECTOR: F-09
AK
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-330
STEP 28. Check the ground circuit to the rear combination
lamp (LH). Measure the resistance at rear combination
lamp (LH) connector F-09.
(1) Disconnect rear combination lamp (LH) connector F-09 and
measure the resistance available at the wiring harness side
of the connector.
(2) Measure the resistance value between terminal 2 and
ground.
• The resistance should be 2 ohms or less.
Q: Is the measured resistance 2 ohms or less?
YES : Go to Step 30.
NO : Go to Step 29.
STEP 29. Check the wiring harness between rear
combination lamp (LH) connector F-09 (terminal 2) and
ground.
Q: Is the wiring harness between rear combination lamp
(LH) connector F-09 (terminal 2) and ground in good
condition?
YES : Replace the rear combination lamp socket assembly
(LH). Verify that the turn-signal lamps illuminate
normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the turn-signal lamps illuminate normally.
AC305260
HARNESS SIDE
CONNECTOR: F-09
AK
AC209364HF
CONNECTOR F-09
(HARNESS SIDE)
AC305260
HARNESS SIDE
CONNECTOR: F-09
AK
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-331
STEP 30. Check ETACS-ECU connector C-219 for loose,
corroded or damaged terminals, or terminals pushed back
in the connector.
Q: Is ETACS-ECU connector C-219 in good condition?
YES : Go to Step 31.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the turn-signal lamps illuminate
normally.
STEP 31. Check the wiring harness between rear
combination lamp (LH) connector F-09 (terminal 5) and
ETACS-ECU connector C-219 (terminal 14).
54DB014A
CONNECTOR: C-219
JUNCTION BLOCK SIDE
JUNCTION BLOCK
(REAR VIEW)
54DB014A
CONNECTOR: C-219
JUNCTION BLOCK SIDE
JUNCTION BLOCK
(REAR VIEW)
AC305260
HARNESS SIDE
CONNECTOR: F-09
AK
SYMPTOM PROCEDURES
SIMPLIFIED WIRING SYSTEM (SWS)
54B-332
NOTE: Also check junction block connector C-204 for loose,
corroded, or damaged terminals, or terminals pushed back in
the connector. If junction block connector C-204 is damaged,
repair or replace the damaged component(s) as described in
GROUP 00E, Harness Connector Inspection
Q: Is the wiring harness between rear combination lamp
(LH) connector F-09 (terminal 5) and ETACS-ECU
connector C-219 (terminal 14) in good condition?
YES : Replace the rear combination lamp socket assembly
(LH). Verify that the turn-signal lamps illuminate
normally.
NO : The wiring harness may be damaged or the
connector(s) may have loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Repair the wiring harness as necessary. Verify that
the turn-signal lamps illuminate normally.
STEP 32. Check rear combination lamp (RH) connector
F-03 for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Is rear combination lamp (RH) connector F-03 in good
condition?
YES : Go to Step 33.
NO : Repair or replace the damaged component(s). Refer
to GROUP 00E, Harness Connector Inspection
. Verify that the turn-signal lamps illuminate
normally.
STEP 33. Check the rear turn-signal lamp bulb (RH).
(1) Remove the rear turn-signal (RH) lamp bulb.
(2) Verify that the rear turn-signal lamp bulb (RH) is not
damaged or burned out.
Q: Is the rear turn-signal (RH) lamp bulb in good
condition?
YES : Go to Step 34.
NO : Replace the rear turn-signal (RH) lamp bulb. Verify
that the turn-signal lamps illuminate normally.
AC305260
AH
CONNECTOR: F-03
HARNESS SIDE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст