Mitsubishi 380. Manual — part 182
AUTO A/C DIAGNOSIS
HEATER, AIR CONDITIONING AND VENTILATION
55-24
STEP 3. Using diagnostic tool , check data list item 20: Air
thermo sensor.
CAUTION
To prevent damage to diagnostic tool , always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting diagnostic tool .
(1) Connect diagnostic tool to the data link connector.
(2) Ignition switch: ON
(3) Set diagnostic tool to the data reading mode for item 20: Air
thermo sensor.
• Check that the passenger room temperature matches
the displayed value on the diagnostic tool while the
engine is cold.
NOTE: When this DTC is set and the system is fail-safe sta-
tus, the value of service data displays
−6°C.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor within the specified range?
YES : Replace the A/C-ECU. Then go to Step 7.
NO : Go to Step 4.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AUTO A/C DIAGNOSIS
HEATER, AIR CONDITIONING AND VENTILATION
55-25
STEP 4. Check A/C-ECU connector C-15, C-16 and air
thermo sensor connector C-126 for loose, corroded or
damaged terminals, or terminals pushed back in the
connector.
Q: Are A/C-ECU connector C-15, C-16 and air thermo
sensor connector C-126 in good condition?
YES : Go to Step 5.
NO : Repair or replace the connector. Refer to GROUP
00E, Harness Connector Inspection
to Step 7.
25DB080A
CONNECTOR: C-126
HARNESS SIDE
25DB070A
CONNECTORS: C-15, C-16
C-16 (B)
HARNESS SIDE
C-16
C-15
C-15 (B)
HARNESS SIDE
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
AUTO A/C DIAGNOSIS
HEATER, AIR CONDITIONING AND VENTILATION
55-26
STEP 5. Check the wiring harness between A/C-ECU
connector C-15 (terminal 20), C-16 (terminal 24) and air
thermo sensor connector C-126 (terminals 2 and 1).
Q: Is the wiring harness between A/C-ECU connector C-10
(terminal 10 and 13) and air thermo sensor connector
C-126 (terminals 2 and 1) in good condition?
YES : Go to Step 6.
NO : Repair the wiring harness. Then go to Step 7.
25DB080A
CONNECTOR: C-126
HARNESS SIDE
25DB070A
CONNECTORS: C-15, C-16
C-16 (B)
HARNESS SIDE
C-16
C-15
C-15 (B)
HARNESS SIDE
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
AUTO A/C DIAGNOSIS
HEATER, AIR CONDITIONING AND VENTILATION
55-27
STEP 6. Check the air thermo sensor.
(1) Disconnect the air thermo sensor connector C-126.
(2) Measure the resistance between connector terminals 1 and
2 under at least two different temperatures. The resistance
values should generally match those in the graph.
NOTE: The temperature at the check should not exceed the
range in the graph.
Q: Is the air thermo sensor in good condition?
YES : Replace the A/C-ECU. Then go to Step 7.
NO : Replace the air thermo sensor. Then go to Step 7.
STEP 7. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Connect diagnostic tool to the data link connector
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the check result satisfactory?
YES : The procedure is complete.
NO : Return to Step 1.
25DB080A
CONNECTOR: C-126
HARNESS SIDE
AC001043
RESISTANCE kΩ
8
6
4
2
0
-10
0
10
20
30
40
TEMPERATURE ˚C(˚F)
AB
(14)
(32)
(50)
(86) (104)
(68)
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст