Mitsubishi 380. Manual — part 768
FUEL TANK
FUEL SUPPLY
13B-12
<<E>> FUEL PUMP MODULE REMOVAL
CAUTION
When withdrawing the fuel pump module from the fuel
tank, be careful not to damage the module unit and the
float.
Make alignment marks between the suction hose and the fuel
pump module and then disconnect the suction hose to remove
the fuel pump module.
.
<<F>> FUEL LEVEL SENSOR (SUB) REMOVAL
CAUTION
When withdrawing the fuel level sensor (sub) from the fuel
tank, be careful not to damage the sensor unit and the
float.
1.Remove the fuel level sensor (sub) mounting bolts and
remove the fuel tank gauge unit from the tank hole.
AC307207
FUEL PUMP
MODULE
FLOAT
AB
AC306092AB
SUCTION HOSE
FUEL PUMP
MODULE
MATING MARKS
AC307206AB
FLOAT
FUEL LEVEL
SENSOR (SUB)
FUEL TANK
FUEL SUPPLY
13B-13
INSTALLATION SERVICE POINTS
.
>>A<< FUEL LEVEL SENSOR (SUB) INSTALLA-
TION
CAUTION
When inserting the fuel level sensor (sub) into the fuel
tank, be careful not to damage the sensor unit and the
float.
1. Install the fuel level sensor to the fuel tank hole.
.
>>B<< FUEL PUMP MODULE INSTALLATION
CAUTION
When installing the fuel pump module into the fuel tank, be
careful not to damage the module unit and the float.
1. Align the mark of the suction hose with that of the fuel pump
module, and then connect the suction hose to the fuel pump
module.
2. Install the fuel pump module into the fuel tank while ensuring
that the suction hose is not kinked.
.
AC307206AB
FLOAT
FUEL LEVEL
SENSOR (SUB)
AC307207
FUEL PUMP
MODULE
FLOAT
AB
AC306092AB
SUCTION HOSE
FUEL PUMP
MODULE
MATING MARKS
FUEL TANK
FUEL SUPPLY
13B-14
>>C<< FUEL HIGH-PRESSURE HOSE/FUEL
HIGH-PRESSURE HOSE CONNECTION
INSTALLATION
CAUTION
Connect the fuel high-pressure hose, and then pull it gen-
tly in the direction of removal to check that the hose is
firmly connected.
Apply clean engine oil to the tips of the main pipe nozzle and
the fuel main pipe, and connect connector of the fuel high-pres-
sure hose to them.
.
>>D<< FUEL TANK BAND/FUEL TANK ASSEMBLY
INSTALLATION
1. Raise the fuel tank assembly carefully with a transaxle jack.
2. Ensure that the fuel tank assembly does not interfere with
surrounding parts. Then install the fuel tank band and
tighten the mounting nuts to the specified torque.
Tightening torque: 26
± 4 N⋅m (19 ± 3 ft-lb)
3. Again, ensure that the fuel tank assembly does not interfere
with surrounding components. If the fuel tank assembly
interferes surrounding components, remove the fuel tank
assembly and the tank band and reinstall them.
INSPECTION
M1135002000241
.
FUEL SHUT-OFF VALVE CHECK
Check that the flapper of the fuel shut-off valve opens and
closes as shown in the illustration.
AC209221
CONNECTOR
MAIN PIPE NOZZLE OR
FUEL MAIN PIPE
AB
AC005004A
CLOSED
OPEN
FLAPPER
80°
03DB148A
SPECIFICATIONS
FUEL SUPPLY
13B-15
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
M1135003900322
SERVICE SPECIFICATION
M1135000300257
ITEM
SPECIFICATIONS
Fuel tank band nut
26
± 4 N⋅m (19 ± 3 ft-lb)
Hole cover screw
1.5
± 0.5 N⋅m (14 ± 4 in-lb)
ITEM
STANDARD VALUE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст