Mitsubishi 380. Manual — part 375
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-40
STEP 5. Check the transmission fluid temperature sensor
at A/T control solenoid valve assembly connector B-108.
(1) Disconnect connector B-108 and measure at the sensor
side.
(2) Measure the resistance between terminal 1 and 2.
• When transmission fluid temperature is 0°C (32°F),
resistance should be between 16.7 and 20.5 k
Ω.
• When transmission fluid temperature is 20°C (68°F),
resistance should be between 7.3 and 8.9 k
Ω.
• When transmission fluid temperature is 40°C (104°F),
resistance should be between 3.4 and 4.2 k
Ω.
• When transmission fluid temperature is 60°C (140°F),
resistance should be between 1.9 and 2.2 k
Ω.
• When transmission fluid temperature is 80°C (176°F),
resistance should be between 1.0 and 1.2 k
Ω.
• When transmission fluid temperature is 100°C (212°F),
resistance should be between 0.57 and 0.69 k
Ω.
Q: Is the measured resistance within the specified range?
YES : Go to Step 6.
NO : Replace the transmission fluid temperature sensor.
Refer to GROUP 23B, Transmission
AC306322
CONNECTOR: B-108
B-108 (GR)
AC
TRANSMISSION
RANGE SWITCH
2
7
1
8
3
9
4
6
10
5
2
7
1
8
3
9
4
6
10
5
AC209994AB
B-108 HARNESS
CONNECTOR:
TRANSMISSION FLUID
TEMPERATURE SENSOR SIDE
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-41
STEP 6. Using diagnostic tool MB991958, check data list
item 7: Transmission Fluid Temperature Sensor.
CAUTION
To prevent damage to diagnostic tool MB991958, always
turn the ignition switch to the "LOCK" (OFF) position
before connecting or disconnecting diagnostic tool
MB991958.
(1) Connect diagnostic tool MB991958 to the data link
connector.
(2) Start the engine.
(3) Set diagnostic tool MB991958 to the data reading mode.
• Item 7: Transmission Fluid Temperature Sensor.
• When the engine is cool: Diagnostic tool display is
almost equal to the ambient temperature (atmo-
spheric temperature)
NOTE: Set diagnostic tool MB991958 to the Engine
MPI data list reading mode for item number 5, Intake
Air Temperature (IAT) Sensor and note the tempera-
ture measurement. When the engine is cool, the
temperature should be almost equal to the ambient
temperature (atmospheric temperature), and the IAT
sensor measurement should be approximately the
same as the Transmission Fluid Temperature Sen-
sor.
• When the engine is warm, at approximately running
temperature: 70
− 80°C.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the sensor operating properly?
YES : It can be assumed that this malfunction is intermittent.
Refer to GROUP 00, How to Use
Troubleshooting/Inspection Service Points
− How to
Cope with Intermittent Malfunction
NO : Replace the A/T-ECU.
STEP 7. Check A/T control solenoid valve assembly
connector B-108 for loose, corroded or damaged
terminals, or terminals pushed back in the connector.
Q: Are the connector and terminals in good condition?
YES : Go to Step 8.
NO : Repair or replace the damaged components. Refer to
GROUP 00E, Harness Connector Inspection
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AC306322
CONNECTOR: B-108
B-108 (GR)
AC
TRANSMISSION
RANGE SWITCH
2
7
1
8
3
9
4
6
10
5
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-42
STEP 8. Measure the resistance of the ground circuit at A/T
control solenoid valve assembly connector B-108.
(1) Disconnect connector B-108 and measure at the harness
side.
(2) Measure the resistance between terminal 2 and ground.
• The resistance should measure less than 2 ohms.
Q: Is the resistance less than 2 ohms?
YES : Go to Step 5.
NO : Go to Step 12.
AC306322
CONNECTOR: B-108
B-108 (GR)
AC
TRANSMISSION
RANGE SWITCH
2
7
1
8
3
9
4
6
10
5
2
5
6
10
4
9
3
8
1
7
AC209995
B-108 HARNESS
CONNECTOR:
COMPONENT SIDE
AB
AUTOMATIC TRANSMISSION DIAGNOSIS
AUTOMATIC TRANSMISSION
23A-43
STEP 9. Measure the sensor output voltage at A/T-ECU
connector B-22 by using check harness special tool
MB992045 .
(1) Disconnect all the connectors from the A/T-ECU.
(2) Connect special tool MB992045 (check harness) between
the A/T-ECU and the body-side harness connector.
(3) Turn the ignition switch to the "ON" position.
(4) Measure the voltage between connector B-22 (terminal 6)
and ground.
• When transmission fluid temperature is 20°C (68°F),
voltage should measure between 3.8 and 4.0 volts.
• When transmission fluid temperature is 40°C (104°F),
voltage should measure between 3.2 and 3.4 volts.
• When transmission fluid temperature is 80°C (176°F),
voltage should measure between 1.7 and 1.9 volts.
(5) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the measured voltage within the specified range?
YES : Go to Step 6.
NO : Go to Step 10.
16DB564A
COVER
AIR
CLEANER
A/T
CONTROL
UNIT
CONNECTORS: B-19, B-22
10DB161A
A/T-ECU CHECK HARNESS
MB992045
A/T-ECU
A/T-ECU CHECK
HARNESS
CONNECTORS
10DB081A
B-22 CONNECTOR:
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст