Mitsubishi 380. Manual — part 179
AUTO A/C DIAGNOSIS
HEATER, AIR CONDITIONING AND VENTILATION
55-12
STEP 3. Using diagnostic tool , check data list item 59:
Inside temperature sensor.
CAUTION
To prevent damage to diagnostic tool , always turn the
ignition switch to the "LOCK" (OFF) position before con-
necting or disconnecting diagnostic tool .
(1) Connect diagnostic tool to the data link connector.
(2) Start the engine.
(3) Set diagnostic tool to the data reading mode for item 59:
Inside temperature sensor.
• Check that the interior temperature matches the dis-
played value on the diagnostic tool.
NOTE: When this DTC is set and the system is in fail-safe
status, the value of service data displays 25
°C.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Does the interior temperature match the displayed value
on the diagnostic tool?
YES : Replace the A/C-ECU. Then go to Step 7.
NO : Go to Step 4.
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
AUTO A/C DIAGNOSIS
HEATER, AIR CONDITIONING AND VENTILATION
55-13
STEP 4. Check A/C-ECU connector C-15, C-16 and interior
temperature sensor connector C-123 for loose, corroded
or damaged terminals, or terminals pushed back in the
connector.
Q: Are A/C-ECU connectors C-15, C-16 and interior
temperature sensor connector C-123 in good condition?
YES : Go to Step 5.
NO : Repair or replace the connector. Refer to GROUP
00E, Harness Connector Inspection
to Step 7.
25DB070A
CONNECTORS: C-15, C-16
C-16 (B)
HARNESS SIDE
C-16
C-15
C-15 (B)
HARNESS SIDE
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
25DB071A
CONNECTOR: C-123
HARNESS SIDE
AUTO A/C DIAGNOSIS
HEATER, AIR CONDITIONING AND VENTILATION
55-14
STEP 5. Check the wiring harness between A/C-ECU
connector C-15 (terminals 20), C-16 (terminals 22) and
interior temperature sensor connector C-123 (terminals 1
and 2).
Q: Are the wiring harnesses between A/C-ECU connector
C-15 (terminals 20), C-16 (terminals 22) and interior
temperature sensor connector C-123 (terminals 1 and 2)
in good condition?
YES : Go to Step 6.
NO : Repair the wiring harness. Then go to Step 7.
25DB070A
CONNECTORS: C-15, C-16
C-16 (B)
HARNESS SIDE
C-16
C-15
C-15 (B)
HARNESS SIDE
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
25DB072A
CONNECTORS: C-03, C-123
C-03
C-123
JUNCTION BLOCK SIDE
C-03
HARNESS SIDE
C-123
AUTO A/C DIAGNOSIS
HEATER, AIR CONDITIONING AND VENTILATION
55-15
STEP 6. Check the interior temperature sensor.
(1) Disconnect interior temperature sensor connector C-123.
(2) When the resistance between the sensor terminals is
measured under two or more temperature conditions, the
resistance should approximately satisfy the illustrated
values.
NOTE: The temperature conditions when checking should
not exceed the range shown in the diagram.
Q: Is the interior temperature sensor in good condition?
YES : Replace the A/C-ECU. Then go to Step 7.
NO : Replace the interior temperature sensor. Then go to
Step 7.
STEP 7. Recheck for diagnostic trouble code.
Check again if the DTC is set.
(1) Connect diagnostic tool to the data link connector
(2) Turn the ignition switch to the "ON" position.
(3) Check if the DTC is set.
(4) Turn the ignition switch to the "LOCK" (OFF) position.
Q: Is the check result satisfactory?
YES : The procedure is complete.
NO : Return to Step 1.
25DB071A
CONNECTOR: C-123
HARNESS SIDE
AC103488 AC
RESISTANCE
(kΩ)
TEMPERATURE ˚C (˚F)
20
15
10
5
0
0
20
40
60
80
-10
(32) (68) (104) (140) (176)
(14)
00DB076A
MB991910
DATA LINK
CONNECTOR
MB991824
MB991827
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст