Mitsubishi 380. Manual — part 846
LOWER ARM
REAR SUSPENSION
34-10
LOWER ARM
REMOVAL AND INSTALLATION
M1341006500047
CAUTION
*
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in an unladen condition.
Post-installation Operation
• Rear Wheel Alignment Check and Adjustment (Refer to
).
AC305777
1
2
5
AB
78 ± 7 N·m*
57 ± 5 ft-lb*
N
113 ± 12 N·m*
83 ± 9 ft-lb*
40 ± 5 N·m
30 ± 3 ft-lb
3
4
REMOVAL STEPS
•
SHOCK ABSORBER ASSEMBLY
AND KNUCKLE CONNECTION
(REFER TO
).
1.
LOWER ARM ASSEMBLY AND
STABILIZER BAR LINK ASSEMBLY
CONNECTION
2.
LOWER ARM ASSEMBLY AND
KNUCKLE CONNECTION
<<A>>
3.
LOWER ARM BOLT
4.
LOWER ARM PLATE
5.
LOWER ARM ASSEMBLY
REMOVAL STEPS (Continued)
LOWER ARM
REAR SUSPENSION
34-11
REMOVAL SERVICE POINT
.
<<A>> LOWER ARM BOLT REMOVAL
Place mating marks on the crossmember and the plate before
removing the lower arm bolt.
INSPECTION
M1341006600055
• Check the bushings for wear and deterioration.
• Check the lower arm for bending or breakage.
• Check all bolts for condition and straightness.
AC306251
AB
LOWER ARM
ASSEMBLY
CROSSMEMBER
PLATE
MATING MARKS
TRAILING ARM
REAR SUSPENSION
34-12
TRAILING ARM
REMOVAL AND INSTALLATION
M1341002200390
CAUTION
*
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in an unladen condition.
NOTE: Bolt A and nut B are interchangeable.
INSPECTION
M1341002300201
• Check the bushings for wear and deterioration.
• Check the trailing arm for bending or breakage.
• Check all bolts for condition and straightness.
Post-installation Operation
• Rear Wheel Alignment Check and Adjustment (Refer to
).
17DB050A
1
2
3
113 ± 12 N·m*
83 ± 9 ft-lb*
N
N
113 ± 12 N·m*
83 ± 9 ft-lb*
105 ± 10 N·m
77 ± 7 ft-lb
A
B
A
B
REMOVAL STEPS
1.
TRAILING ARM ASSEMBLY AND
KNUCKLE CONNECTION
2.
TRAILING ARM ASSEMBLY
3.
TRAILING ARM BRACKET
REMOVAL STEPS (Continued)
TOE CONTROL ARM
REAR SUSPENSION
34-13
TOE CONTROL ARM
REMOVAL AND INSTALLATION
M1341016600045
CAUTION
*
: Indicates parts which should be temporarily tightened, and then fully tightened with the vehicle on
the ground in an unladen condition.
Required Special Tool:
• MB991897: Ball Joint Remover
Post-installation Operation
• Press the dust cover with your finger to check that there
are no cracks or damage in the dust cover.
• Rear Wheel Alignment Check and Adjustment (Refer to
).
AC305779
AC205712
2
AB
78 ± 7 N·m*
57 ± 5 ft-lb*
66 ± 6 N·m
49 ± 4 ft-lb
3
4
4
MULTIPURPOSE GREASE
SAE J310, NLGI No.2
OR EQUIVALENT
7 ± 0.5 g
(0.247 ± 0.018 oz)
1
2
78 ± 7 N·m
57 ± 5 ft-lb
N
REMOVAL STEPS
•
TRAILING ARM ASSEMBLY AND
KNUCKLE CONNECTION (REFER
TO
).
<<A>>
1.
TOE CONTROL ARM ASSEMBLY
AND KNUCKLE CONNECTION
<<B>>
2.
ASSIST LINK BOLT
3.
ASSIST LINK PLATE
4.
TOE CONTROL ARM ASSEMBLY
REMOVAL STEPS (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст