Mitsubishi ASX (2018 year). Instruction — part 4

NOTE

l

In a vehicle that has a Dead Lock System, it
is not possible to unlock the door by pushing
the lock knob to the unlock side while the
Dead Lock System is set.
(Refer to “Dead Lock System” on page
3-27.)

To lock without using the key

Front passenger’s door, Rear

door

Set the inside lock knob (1) to the locked po-
sition, and close the door (2).

NOTE

l

The driver’s door cannot be locked using the
inside lock knob while the driver’s door is
opened.

Operation mode ON reminder

system*

E00310100268

For vehicles equipped with the keyless op-
eration system

If the driver’s door is opened with the engine
stopped and the operation mode in any posi-
tion other than OFF, the operation mode ON
reminder buzzer sounds intermittently to re-
mind you to put the operation mode in OFF.
In addition, the warning display will be dis-
played on the information screen in the multi-
information display.

Central door locks

E00300801777

NOTE

l

Each of the doors can be locked or unlocked
independently by using the inside lock knob.

l

When locking or unlocking with the key on
the driver’s door, only the driver’s door will
lock or unlock.

NOTE

l

Repeated continuous operation between lock
and unlock could activate the central door
locking systems built-in protection circuit
and prevent the system from operating.
If this occurs, wait approximately 1 minute
before operating the central door lock
switch.

l

When the driver’s door is open, the central
door lock switch cannot be used to lock it.

To lock and unlock the doors

and tailgate

Using the central door lock

switch

Using the central door lock switch on the
driver’s door locks or unlocks all doors and
the tailgate.

LHD

Central door locks

3-26

OGAE18E1

Locking and unlocking

3

RHD

1- Lock
2- Unlock

To unlock the doors and tail-

gate

E00311301453

You can select the functions to unlock the
doors and tailgate either using the ignition
switch or the engine switch, or using the se-
lector lever position A/T or CVT).
These functions are not activated when the
vehicle is shipped from the factory. To acti-
vate or deactivate these functions, please
contact a MITSUBISHI MOTORS Author-
ized Service Point.

Using the ignition switch or the

engine switch

All doors and the tailgate will unlock when-
ever the ignition switch is turned to the
“LOCK” position or the operation mode is
put in OFF.

Using the selector lever position

(A/T or CVT)

All doors and the tailgate will unlock when-
ever the selector lever is moved to the “P”
(PARK) position with the ignition switch in
the “ON” position or the operation mode in
ON.

Dead Lock System*

E00305100130

The Dead Lock System helps to prevent
theft. When the keyless entry system or the
keyless operation system has been used to
lock all of the doors and the tailgate, the
Dead Lock System makes it impossible to
unlock the doors using the inside lock knobs.

CAUTION

l

Do not set the Dead Lock System when
someone is inside the vehicle. With the Dead
Lock System set, it is not possible to unlock
the doors using the inside lock knobs. If you
erroneously set the Dead Lock System, un-
lock the doors using the UNLOCK switch
on the remote control switch or using the
keyless operation function.

Setting the system

E00305201369

1. Except for vehicles equipped with the

keyless operation system, remove the
key from the ignition switch.
For vehicles equipped with the keyless
operation system, put the operation
mode in OFF.

2. Get out of the vehicle. Close all of the

doors and the tailgate.

3. Press the LOCK switch (A) on the re-

mote control switch, the driver’s or front
passenger’s door lock/unlock switch (B),
or the tailgate LOCK switch (C) to lock
all of the doors and the tailgate. The
turn-signal lamps will blink once.

Dead Lock System*

3-27

OGAE18E1

Locking and unlocking

3

4. Press the switch again within 2 seconds.

The turn-signal lamps will blink three
times to show that the Dead Lock Sys-
tem has been set.

Except for vehicles equipped with the keyless
operation system

Vehicles equipped with the keyless operation system

Driver’s and front passenger’s door lock/unlock
switches*

Tailgate LOCK switch*

NOTE

l

Pressing the LOCK switch (A) on the re-
mote control switch once while the Dead
Lock System is set causes the turn-signal
lamps to blink three times, so it is possible to
confirm that the Dead Lock System is set.

Cancelling the system

E00305301416

When the following operation is performed,
the doors and tailgate will unlock and the
Dead Lock System will be simultaneously
cancelled.

l

The UNLOCK switch (D) on the remote
control switch is pressed.

l

The driver’s or front passenger’s door
lock/unlock switch (E) or the tailgate
OPEN switch (F) is pressed while you
are carrying the keyless operation key.

Except for vehicles equipped with the keyless
operation system

Dead Lock System*

3-28

OGAE18E1

Locking and unlocking

3

Vehicles equipped with the keyless operation system

Driver’s and front passenger’s door lock/unlock
switches*

Tailgate OPEN switch

NOTE

l

If neither a door nor the tailgate is opened
within 30 seconds of unlocking (except us-
ing the tailgate OPEN switch), the doors and
tailgate are automatically relocked and the
Dead Lock System is simultaneously set
again.

l

Even when it is not possible to use the key-
less entry system or keyless operation func-
tion to unlock the doors, it is possible to use
the key to unlock the driver’s door. When
the key is used to unlock the driver’s door,
the Dead Lock System is cancelled for only
the driver’s door. If you wish to subsequent-
ly unlock all other doors, perform the fol-
lowing operation.

•

Except for vehicles equipped with the
keyless operation system, turn the ignition
switch to the “ON” or “ACC” position.

•

For vehicles equipped with the keyless
operation system, put the operation mode
in ON or ACC.

l

It is possible to adjust the time between
pressing the UNLOCK switch (D) on the re-
mote control switch or the driver’s or front
passenger’s door lock/unlock switch (E) and
automatic locking. For details, please con-
tact a MITSUBISHI MOTORS Authorized
Service Point.

NOTE

l

It is possible to lock the doors and tailgate
and set the Dead Lock System at the same
time with a single push of the LOCK switch
(A) on the remote control switch, the driv-
er’s or front passenger’s door lock/unlock
switch (B), or the tailgate LOCK switch (C).
For details, please contact a MITSUBISHI
MOTORS Authorized Service Point.

Testing the system

E00305400104

Open all of the door windows, then set the
Dead Lock System. (Refer to “Setting the
system” on page 3-27.)
After setting the Dead Lock System, reach
into the vehicle through a window and con-
firm that you cannot unlock the doors using
the lock knobs.

NOTE

l

If you need advice on how to set the Dead
Lock System, please contact a MITSUBISHI
MOTORS Authorized Service Point.

Dead Lock System*

3-29

OGAE18E1

Locking and unlocking

3

“Child-protection” rear
doors

E00300900999

1- Lock
2- Unlock

Child protection helps prevent the rear doors
from being opened accidentally from the in-
side.
If the lever is set to the locked position, the
rear door cannot be opened using the inside
handle, but only with the outside handle.
If the lever is set to the “Unlock” position,
the child protection mechanism does not
function.

CAUTION

l

When driving with a child in the rear seat,
please use the child protection to prevent ac-
cidental door opening which may cause an
accident.

Tailgate

E00301402836

WARNING

l

The luggage compartment was not de-
signed for people to ride in it. Do not let
passengers ride in or let children play in
the luggage compartment. Riding or play-
ing in the luggage compartment could re-
sult in a serious accident.

l

It is dangerous to drive with the tailgate
open, since carbon monoxide (CO) gas
contained in engine exhaust gases can en-
ter the cabin.
You cannot see or smell CO. It can cause
unconsciousness and even death.
In addition, if the tailgate opens when
driving, luggage could fall onto the road
and cause an accident.

l

When opening and closing the tailgate,
make sure that there are no people near-
by and that there is sufficient space be-
hind and above the vehicle. In addition,
be careful not to hit your head or pinch
your hands, neck, etc.

WARNING

l

When there is a build up of snow or ice, it
should be removed before opening the
tailgate. If you open the tailgate without
removing it, there is a possibility that the
tailgate may close suddenly due to the
weight of that snow or ice.

l

When you open the tailgate make sure
that the tailgate is opened fully and re-
mains fully open. If you only open the tail-
gate halfway there is a risk that the tail-
gate may drop and slam shut. If you open
the tailgate while your vehicle is parked
on an incline it is more difficult to do so
than on the flat and also it may drop and
slam shut.

CAUTION

l

Do not stand behind the exhaust pipe when
loading and unloading luggage. The heat
from the exhaust could lead to burns.

l

To avoid damage to the tailgate, make sure
the area above and behind the tailgate is
clear before opening it.

NOTE

l

Locking/unlocking with the central door
lock switch, the keyless entry system, or the
keyless operation function also locks/
unlocks the tailgate.

“Child-protection” rear doors

3-30

OGAE18E1

Locking and unlocking

3

To open

After unlocking, press the tailgate OPEN
switch (A) and lift the tailgate.

NOTE

l

If you do not open the tailgate immediately
after pressing the tailgate OPEN switch, the
tailgate can not be lifted. If this happens,
press the tailgate OPEN switch again and lift
the tailgate.

l

The tailgate cannot be opened when the bat-
tery is flat or disconnected.

To close

Pull the tailgate grip (A) downward as illus-
trated. Gently push the upper gate from the
outside with enough force so that it is com-
pletely closed. Always ensure the tailgate is
securely closed.

CAUTION

l

Do not close the tailgate completely by hold-
ing the tailgate grip (A). Your hand or arm
could be pinched and personal injury could
result.

NOTE

l

Gas struts (B) are installed to support the
tailgate.

NOTE

To prevent damage or faulty operation.

•

Do not hold the gas struts when closing
the tailgate.

•

Also, do not push or pull the gas struts.

•

Do not attach any plastic material, tape,
etc., to the gas struts.

•

Do not tie string, etc., around the gas
struts.

•

Do not hang any object on the gas struts.

Inside tailgate release

E00303401354

The inside tailgate release is designed to pro-
vide a way to open the tailgate in the case of
a discharged battery.

Inside tailgate release

3-31

OGAE18E1

Locking and unlocking

3

The tailgate release lever (see illustration) is
mounted on the tailgate.

You and your family should familiarize your-
selves with the location and operation of the
tailgate release lever.

To open

1. Insert a straight blade (or minus) screw-

driver into the notch of the lid (A) and
pry gently to open the lid.

2. Move the lever (B) to open the tailgate.

3. Push out on the tailgate to open it.

WARNING

l

Always keep the lid (A) on the tailgate
closed when driving so that your luggage
cannot accidentally bump the lever (B)
and open the tailgate.

Security alarm system*

E00301502329

The security alarm system is for alerting the
surrounding area of suspicious behaviour to
prevent unlawful entry into the vehicle by op-
erating an alarm if a door, the tailgate or the
bonnet is opened when the vehicle has not
been unlocked using the keyless entry system
or the keyless operation function.
Also, the alarm will be activated if any of the
following occur.

l

Attempt to an unlawful moving of the
vehicle (the vehicle inclination detection
function)

l

Detection of a motion in the vehicle (the
interior intrusion detection function)

l

Disconnect the battery terminal.

The security alarm system is set to “active”.
When making changes to the settings, please
follow the procedure listed in the section ti-
tled “Changing the security alarm settings”
on page 3-34.

CAUTION

l

Do not modify or add parts to the security
alarm system.
Doing so could cause the security alarm to
malfunction.

NOTE

l

The alarm system will not be activated if the
doors and the tailgate have been locked us-
ing a key, the inside lock knob or the central
door lock switch (instead of the keyless en-
try system or the keyless operation func-
tion).

Security alarm system*

3-32

OGAE18E1

Locking and unlocking

3

NOTE

l

If the turn-signal lamps do not blink after the
locking and unlocking operation using the
keyless entry system or the keyless operation
function, the security alarm system may be
malfunctioning.
Have

the

vehicle

inspected

at

a

MITSUBISHI MOTORS Authorized Serv-
ice Point.
If the confirmation function (blinking of the
turn-signal lamps by locking and unlocking
the doors and the tailgate) is deactivated, the
turn-signal lamps do not blink after the lock-
ing and unlocking operation.
For information on the confirmation func-
tion, refer to “Keyless entry system” on pa-
ges 3-04, 3-22 and “To operate using the
keyless operation function” on page 3-10.

l

The security alarm system could be activated
in the following situations.

•

Using a car wash

•

Taking the vehicle on a ferry

•

Parking in an automated car park

•

Leaving someone or a pet in the vehicle

•

Leaving a window open

•

Leaving an unstable object such as a stuf-
fed toy or accessory in the vehicle

•

Suffering a continuous impact or vibra-
tion by hail, thunder, etc.

According to the situations, deactivate the
vehicle inclination detection function and
the interior intrusion detection function.
Refer to “To deactivate the vehicle inclina-
tion detection function and the interior intru-
sion detection function” on page 3-37.

NOTE

l

The sensitivity of the interior intrusion de-
tection function can be adjusted. For details,
please contact a MITSUBISHI MOTORS
Authorized Service Point.

The security alarm has four

modes:

System preparation mode (ap-

prox. 20 seconds)

(The buzzer sounds intermittently and the se-
curity indicator (A) blinks.)

The system preparation time extends from
the point at which all of the doors and the
tailgate are locked by pressing the LOCK
switch on the remote control switch or the
keyless operation function to the point at
which the system armed mode goes into ef-
fect.
During this time, it is possible to temporarily
open a door or the tailgate without using the
keyless entry system or the keyless operation
function and without causing the alarm to
sound (for example, when you forget some-
thing inside the vehicle or realize that a win-
dow is open).

System armed mode

(The security indicator continues to blink
with the indicator’s reduced lit-up duration
time.)
Once the system preparation mode has ended,
the system armed mode starts.
If an unlawful opening of any of the doors,
tailgate or bonnet is detected during the sys-
tem armed mode, the alarm will be activated
to warn people around the vehicle of an ab-
normal condition.
Also, if unlawful moving of the vehicle is at-
tempted or a vehicle intrusion is detected, the
alarm will be activated.

Security alarm system*

3-33

OGAE18E1

Locking and unlocking

3

Alarm activation

The turn-signal lamps blink and the siren
sounds for approximately 30 seconds.
Refer to “Alarm activation” on page 3-38.

NOTE

l

The alarm will resume if unlawful actions
are taken again, even if the alarm has stop-
ped.

System cancellation

It is possible to cancel the system activation
during the system preparation mode or the
system armed mode.
In addition, it is possible to cancel the alarm
once it has been activated.
Refer to “Cancelling the system” on page
3-37, “Cancelling the alarm” on page 3-39.

NOTE

l

When lending the vehicle to another person
or allowing the vehicle to be driven by
someone who is unfamiliar with the security
alarm system, be sure to give the person a
proper explanation of the security alarm sys-
tem.
If a person who is unfamiliar with the securi-
ty alarm system accidentally unlocked the
vehicle, causing the alarm to sound, the
alarm would be a nuisance to people nearby.

Changing the security alarm

settings

E00301601440

It is possible to set the security alarm to the
“active” mode or “inactive” mode.
Follow the procedure below.

1. Except for vehicles equipped with the

keyless operation system, remove the
key from the ignition switch. For vehi-
cles equipped with the keyless operation
system, put the operation mode in OFF.

2. Place the lamp switch in the “OFF” posi-

tion, and leave the driver’s door open.

3. Pull the windscreen wiper and washer

switch towards you and hold it there.
(Since the ignition switch is in the
“LOCK” position or the operation mode
is in OFF, washer fluid will not be
sprayed.)

Security alarm system*

3-34

OGAE18E1

Locking and unlocking

3

4. After approximately 10 seconds, the

buzzer will make a sound. Keep the
windscreen wiper and washer switch
pulled towards you. (If the windscreen
wiper and washer switch was released,
the setting change mode would be can-
celled. To start over, perform the proce-
dure again from step 3.)

5. When the buzzer stops, with the wind-

screen wiper and washer switch still
pulled towards you, press the UNLOCK
switch (A) on the remote control switch
to select the security alarm settings
mode.

Except for vehicles equipped with the keyless
operation system

Vehicles equipped with the keyless operation system

The settings mode can be toggled by
pressing the UNLOCK switch. The
mode can be confirmed from the number
of times the buzzer sounds.

Number of

times the

buzzer
sounds

Security alarm settings

mode

1

Alarm inactive

2

Alarm active

6. Any of the following operations can be

used to terminate the system settings
change mode.

• Releasing the windscreen wiper and

washer switch.

• Closing the driver’s door.

• Inserting the key into the ignition

switch (except for vehicles equip-
ped with the keyless operation sys-
tem).

• Putting the operation mode in ON

or ACC. (vehicles equipped with
the keyless operation system)

• Placing the lamp switch in any posi-

tion other than “OFF”.

• Allowing 30 seconds to pass with-

out making any changes to the set-
tings.

NOTE

l

If anything with regard to making changes to
the security alarm system settings is hard to
understand,

please

consult

your

MITSUBISHI MOTORS Authorized Serv-
ice Point.

l

Avoid leaving valuable items inside the ve-
hicle even when the security alarm system
has been set to the “active” mode.

Setting the system

E00301702448

Follow the procedure below to set the system
to the system armed mode.

1. Except for vehicles equipped with the

keyless operation system, remove the
key from the ignition switch. For vehi-
cles equipped with the keyless operation
system, put the operation mode in OFF.

Security alarm system*

3-35

OGAE18E1

Locking and unlocking

3

2. Exit the vehicle and close all of the

doors, tailgate and bonnet.

3. Press the LOCK switch (A) on the re-

mote control switch of the keyless entry
system or the keyless operation system,
the driver’s or front passenger’s door
lock/unlock switch (B), or the tailgate
LOCK switch (C) in order to lock all the
doors and the tailgate.

Except for vehicles equipped with the keyless
operation system

Vehicles equipped with the keyless operation system

Driver’s and front passenger’s door look/unlock switches*

Tailgate LOCK switch*

By locking the vehicle using the keyless
entry system or the keyless operation
function, the system preparation mode is
activated.
The buzzer makes an intermittent beep-
ing sound and the security indicator (D)

in the audio panel blinks for confirma-
tion.

NOTE

l

The system preparation mode is not activa-
ted when the doors and the tailgate have
been locked using a method other than the
keyless entry system or the keyless operation
function (namely a key, the inside lock knob
or the central door lock switch).

l

If the bonnet is open, the security indicator
illuminates, and the system does not enter
the system preparation mode.
When the bonnet is closed, the system enters
the system preparation mode, and after ap-
proximately 20 seconds the system enters
the system armed mode.

Security alarm system*

3-36

OGAE18E1

Locking and unlocking

3

4. After approximately 20 seconds, the

buzzer stops, and when the blinking of
the security indicator starts to slow
down, the system armed mode goes into
effect.
The security indicator continues to blink
during the system armed mode.

NOTE

l

The security alarm system can be activated
when people are riding inside the vehicle or
when the windows are open. To prevent ac-
cidental activation of the alarm, do not set
the system to the system armed mode while
people are riding in the vehicle.

l

Avoid leaving valuable items inside the ve-
hicle even when the security alarm system
has been set to the “active” mode.

To deactivate the vehicle incli-
nation detection function and
the interior intrusion detection
function

E00312101487

The vehicle inclination detection function
and the interior intrusion detection function
can be deactivated when parking in automa-
ted car parks, when leaving pets in the vehi-
cle or when leaving the vehicle with the win-
dows slightly open.

1. Except for vehicles equipped with the

keyless operation system, remove the
key from the ignition switch. For vehi-
cles equipped with the keyless operation
system, put the operation mode in OFF.

2. Raise and hold the wiper and washer

switch to the “MIST” position for ap-
proximately 3 seconds. The buzzer will
sound twice and the function will be de-
activated.

To activate the function again, raise and hold
the wiper and washer switch to the “MIST”
position for approximately 3 seconds.
The buzzer will sound once and the function
will be activated.

NOTE

l

The function will be activated again if the
following operation is performed.

•

If the doors and the tailgate are unlocked
using the keyless entry system or the key-
less operation function.

•

If the ignition switch is turned to the
“ON” or “ACC” position (except for vehi-
cles equipped with the keyless operation
system).

•

If the operation mode is put in ON or
ACC (vehicles with the keyless operation
system).

Cancelling the system

E00301802003

The following methods can be used to cancel
the system when it is in the system prepara-
tion mode or the system armed mode.

l

Pressing the UNLOCK switch on the re-
mote control switch.

l

Turning the ignition switch to the “ON”
position (except for vehicles equipped
with the keyless operation system).

l

Putting the operation mode in ON (vehi-
cles equipped with the keyless operation
system).

l

Opening any one of the doors or the tail-
gate, or inserting the key into the igni-
tion switch (except for vehicles equipped
with the keyless operation system) when
the system is in the system preparation
mode.

Security alarm system*

3-37

OGAE18E1

Locking and unlocking

3

l

Holding the keyless operation key and
pressing the driver’s or front passenger’s
door lock/unlock switch, or the tailgate
OPEN switch to unlock the doors and
the tailgate (vehicles equipped with the
keyless operation system).

NOTE

l

If the bonnet is opened during the system
preparation mode, the system preparation
condition is suspended.
The system returns to the system preparation
mode when the bonnet is closed.

l

If the battery terminals are disconnected
while the system is in the system preparation
mode, the memory will be erased.

l

It is possible to register up to 8 remote con-
trol switches for the keyless entry system
and 4 remote control switches for the key-
less operation system.
As long as they are registered, any of the re-
mote control switches, other than the one
used to activate the system, can be used to
cancel the system.
If you want to register additional remote
control

switches,

please

contact

a

MITSUBISHI MOTORS Authorized Serv-
ice Point.

NOTE

l

The activation distance for the keyless entry
system is approximately 4 m.
If it is not possible to lock or unlock the ve-
hicle by pressing the switch at the correct
distance or the security alarm system cannot
be set or cancelled using the switch, the bat-
tery may need to be replaced.
For further information, please consult a
MITSUBISHI MOTORS Authorized Serv-
ice Point.
If you replace the battery yourself, refer to
“Procedure for replacing the remote control
switch battery” on pages 3-06, 3-24.

l

If the UNLOCK switch on the remote con-
trol switch, or the driver’s or front passen-
ger’s door lock/unlock switch is pressed and
no door or the tailgate is opened within 30
seconds, the doors and the tailgate will auto-
matically relock. In this case as well, the
system preparation mode will go into effect.

l

The time between pressing the UNLOCK
switch on the remote control switch, or the
driver’s or front passenger’s door lock/
unlock switch and automatic locking can be
adjusted. Please consult a MITSUBISHI
MOTORS Authorized Service Point.

Alarm activation

E00301902310

When the system is in the system armed
mode, the alarm will be activated as follows
if the vehicle is unlocked or if any of the
doors, tailgate or bonnet is opened using a
method other than the keyless entry system or
the keyless operation function.

1. The alarm will be activated for approxi-

mately 30 seconds.
The turn-signal lamps will blink, and the
siren will sound intermittently.

2. The alarm will resume if unlawful ac-

tions are taken again, even if the alarm
has stopped.

Security alarm system*

3-38

OGAE18E1

Locking and unlocking

3

NOTE

l

During an alarm operation, the alarm is dis-
played on the information screen in the mul-
ti-information display.
Type 1

Type 2

Cancelling the alarm

E00302000428

It is possible to halt the activation of an alarm
using the following methods:

l

Pressing the LOCK or UNLOCK switch
on the remote control switch.
(After pressing the LOCK switch, the
vehicle will lock if all the doors and the
tailgate are closed, after which the sys-
tem preparation mode will once again go
into effect.)

l

Turning the ignition switch to the “ON”
position (except for vehicles equipped
with the keyless operation system).

l

Putting the operation mode in ON (vehi-
cles equipped with the keyless operation
system).

l

Holding the keyless operation key and
locking and unlocking the doors and the
tailgate using the keyless operation func-
tion (vehicles equipped with the keyless
operation system).

NOTE

l

When the ignition switch is turned to the
“ON” position or the operation mode is put
in ON, the buzzer sounds 4 times. This oper-
ation indicates that the alarm was activated
while the vehicle was parked.
Please check the inside of the vehicle to con-
firm that nothing was stolen.

l

Even if the battery is disconnected, the alarm
activation memory will not be erased.

Electric window control

E00302200521

The electric windows can only be operated
with the ignition switch in the “ON” position
or the operation mode in ON.

WARNING

l

Before operating the electric window con-
trol, make sure that nothing can get trap-
ped (head, hand, finger, etc.).

l

Never leave the vehicle without removing
the key.

l

Never leave a child (or other person who
might not be capable of safe operation of
the electric window control) in the vehicle
alone.

l

The child may tamper with the switch at
the risk of its hands or head being trap-
ped in the window.

Electric window control switch

E00302303435

Each door window opens or closes while the
corresponding switch is operated.

Driver’s switches (LHD)

Electric window control

3-39

OGAE18E1

Locking and unlocking

3

Driver’s switches (RHD)

1- Driver’s door window
2- Front passenger’s door window
3- Rear left door window
4- Rear right door window
5- Lock switch

Driver’s switches

The switches can be used to operate all door
windows. A window can be opened or closed
by operating the corresponding switch.
Press the switch down to open the window,
and pull up the switch to close it.
If the switch for the driver’s window is fully
pressed down/pulled up, the door window au-
tomatically opens/closes completely.
If you want to stop the window movement,
operate the switch lightly in the reverse direc-
tion.

Passenger’s switches

The passenger’s switches can be used to op-
erate the corresponding passenger’s door
windows. Press the switch down for opening
the window, and pull up the switch for clos-
ing it.

NOTE

l

Repeated operation with the engine stopped
will run down the battery. Operate the elec-
tric window switches only while the engine
is running.

l

The rear door windows only open halfway.

Lock switch

E00303101032

When this switch is operated, the passenger’s
switches cannot be used to open or close the
door windows and the driver’s switch cannot
open or close any door windows other than
the driver’s window.

To unlock, press it once again.

1- Lock
2- Unlock

WARNING

l

A child may tamper with the switch at the
risk of its hands or head being trapped in
the window. When driving with a child in
the vehicle, please press the window lock
switch to disable the passenger’s switches.

Timer function

E00302400800

The door windows can be opened or closed
for 30 seconds after the engine is stopped.
However, once the driver’s door or the front
passenger’s door is opened, the windows can-
not be operated.

Electric window control

3-40

OGAE18E1

Locking and unlocking

3

Safety mechanism (driver’s

door window only)

E00302501895

If a hand or head is trapped in the closing
window, it will lower automatically.
Nonetheless, make sure that nobody puts
their head or hand out of the window when
closing the driver’s door window.
The lowered window will become operation-
al after a few seconds.

WARNING

l

If the battery terminals are disconnected
or the fuse for electric window is replaced,
the safety mechanism will be cancelled.
If a hand or head got trapped, a serious
injury could result.

CAUTION

l

The safety mechanism is cancelled just be-
fore the window is fully closed. This allows
the window to close completely. Therefore
be especially careful that no fingers are trap-
ped in the window.

l

The safety mechanism is deactivated while
the switch is pulled up. Therefore be espe-
cially careful that fingers are not trapped in
the door window opening.

NOTE

l

The safety mechanism can be activated if the
driving conditions or other circumstances
cause the driver’s door window to be subjec-
ted to a physical shock similar to that caused
by a trapped hand or head.

l

If the battery terminals are disconnected or
the fuse for electric window is replaced, the
safety mechanism will be cancelled and the
door window will not automatically open/
close completely.
If the window is open, repeatedly raise the
driver’s door window switch until the win-
dow has been fully closed.
Following this, release the switch, raise the
switch once again and hold it in this condi-
tion for at least 1 second, then release it.
You should now be able to operate the driv-
er’s door window in the normal fashion.

Sunshade*

E00302801407

WARNING

l

Before operating the sunshade, make sure
that nothing can get trapped (head, hand,
finger, etc.).

l

Never leave the vehicle without removing
the key.

l

Never leave a child (or other person who
might not be capable of safe operation of
the sunshade switch) in the vehicle alone.

WARNING

l

Do not bring your head, hand, finger, etc.
near the opening edge of the sunshade re-
ceptacle while the vehicle is in motion.
It may cause injury to your head, hand,
finger, etc. in the event of sudden braking.

CAUTION

l

Do not place heavy luggage on the panoram-
ic glass roof. Doing so could damage the
glass roof.

l

Do not hang heavy luggage from, allow a
person to hang onto, or apply any other
strong force to the opening of the sunshade
receptacle or the parts between the ceiling
and the sunshade opening on either side. Do-
ing so could damage the sunshade.

NOTE

l

Release the switch as soon as the sunshade
reaches the fully open or fully closed posi-
tion.

l

If the sunshade does not operate when the
sunshade switch is operated, release the
switch and check whether something is trap-
ped by the sunshade. If nothing is trapped,
we recommend you to have the sunshade
checked.

l

Operating the sunshade repeatedly with the
engine stationary will run down the battery.
Operate the sunshade while the engine is
running.

Sunshade*

3-41

OGAE18E1

Locking and unlocking

3