Mitsubishi Outlander (2003+). Manual — part 492
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-257
NOTE:
Prior to the wiring harness inspection, check
intermediate connector C-14 <side RH>, C-116
<front or side LH> or D-31 <rear RH (L.H. drive
vehicles)> and junction block connector C-202
<front, side and rear LH (R.H. drivevehicles)>, C-209
<rear (L.H. drivevehicles)> or C-221 <rear RH (R.H.
drivevehicles)> or C-205 <turn-signal indicator
lamp>, and repair if necessary.
•
Check the output lines for open circuit.
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Repair the wiring harness.
AC308718
Connector: C-14
AI
9
3
2
1
5 6 7 8
4
10
<LHD>
AC308769
Connector: C-14
AM
9
3
2
1
5 6 7 8
4
10
<RHD>
AC308721
Connectors: C-202, C-205, C-209
AF
Junction block (Front view)
C-202
C-205
Harness side
C-205
C-202
10
1
6
14
5
12
13
4
11
7
2
3
8
9
C-209
21
7
16 15
17
18
20 19
1
2
3
4
5
6
23 22
24
25
28
26
27
9
8
10
11
14
12
13
7
15
5
6
1413
2
9
12
4 3
10
11
1
8
C-209
<LHD>
AC308773
Connectors: C-202, C-205, C-209
AH
Junction block (Front view)
C-202
C-205
Harness side
C-205
C-202
10
1
6
14
5
12
13
4
11
7
2
3
8
9
C-221
21
7
16 15
17
18
20 19
1
2
3
4
5
6
23 22
24
25
28
26
27
9
8
10
11
14
12
13
7
15
5
6
1413
2
9
12
4 3
10
11
1
8
C-209
<RHD>
AC308781
Connector: D-31
AD
<LHD>
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-258
Step 7. Retest the system.
Check that the turn-signal lamps and the indicator
lamps illuminate normally.
Q: Is the check result normal?
The lamps illuminate normally at both high and low
beams. :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
−
How to
Cope with Intermittent Malfunction
The front turn-signal lamps do not illuminate. :
Replace the socket.
The side turn-signal lamps do not illuminate. :
Replace the socket.
The rear turn-signal lamps do not illuminate. :
Replace the socket assembly.
The turn-signal indicator lamps do not illuminate. :
Replace the combination meter.
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-259
FOG LAMP
INSPECTION PROCEDURE L-1: The front fog lamps do not illuminate normally.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
OPERATION
The ETACS-ECU operates this function in
accordance with the input signals below.
•
Tail lamp switch
•
Headlamp switch
•
Front fog lamp switch
If the front fog lamps do not illuminate normally,
these input signal circuit(s) or the ETACS-ECU may
be defective.
POSSIBLE CAUSES
•
Malfunction of the column switch
•
Malfunction of the front fog lamp switch
•
Malfunction of the ETACS-ECU
•
Damaged harness wires and connectors
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
BATTERY
RELAY
BOX
FRONT FOG
LAMP RELAY
FRONT-ECU
COMBINATION
METER
FRONT
FOG LAMP
(LH)
FRONT
FOG LAMP
(RH)
<LHD>
<RHD>
Front Fog Lamp Circuit
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-260
DIAGNOSTIC PROCEDURE
Step 1. Check that the tail lamps and headlamps
operate.
Check that the tail lamps and headlamps illuminate
normally.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Check the tail lamps and the headlamps
(Refer to trouble symptom chart
).
Step 2. Pulse check
Check the input signals below, which are related to
the front fog lamps.
OK: The MUT-II/III sounds or the voltmeter
needle fluctuates.
Q: Is the check result normal?
All the signals are received normally. :
Go to Step
The ignition switch (IG1) signal is not received. :
Refer to inspection procedure N-2 "The
ignition switch (IG1) signal is not received
The tail lamp switch signal is not received. :
Refer
to inspection procedure N-5 "The column
switch (lighting and turn-signal lamp switch)
signal is not received
The headlamp switch signal is not received. :
Refer to inspection procedure N-5 "The
column switch (lighting and turn-signal lamp
switch) signal is not received
The front fog lamp switch signal is not received. :
Refer to inspection procedure N-15 "The
front fog lamp switch signal is not received
Step 3. Connector check: A-05X front fog lamp
relay connector.
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the defective connector.
Step 4. Check the front fog lamp relay.
Refer to GROUP 54A
−
Front fog lamp
.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Replace the front fog lamp relay.
Step 5. Measure the voltage at the A-05X front fog
lamp relay connector.
(1) Remove the front fog lamp relay, and measure at
the relay box side.
(2) Check the voltage between the front fog lamp
System switch
Check condition
Ignition switch (IG1)
When turned from ACC
to ON
Tail lamp switch
When the lighting switch
is turned to the TAIL
position
Headlamp switch
When the lighting switch
is turned to the
HEADLAMP position
Front fog lamp switch
When the front fog lamp
switch is turned from off
to on
AC301515 AF
Connector: A-05X
1
3
2
4
Front of
vehicle
Relay box side
AC301515 AF
Connector: A-05X
1
3
2
4
Front of
vehicle
Relay box side
AC301541AC
Connector A-05X
(Relay box side)
2
4
1
3
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст