Mitsubishi Outlander (2003+). Manual — part 268
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-15
STEP 7. Check the harness wires between
ABS-ECU connector B-03 (terminals 11 and 17)
and ABS sensor <rear: RH> connector D-13
(terminals 1 and 2).
NOTE:
AC301441AB
Connector: B-03
B-03 (GR)
Harness side
AC301445AB
Connector: D-13
D-13 (B)
Harness side
AC308718
AQ
C-104 (B)
Connector: C-104
<LHD>
15
1
8
3
10
2
9
11
4
13
12
5
14
16
7
6
AC308716
AV
C-117
Connector: C-117
<LHD>
38
1213
11
26
14
1
20
6
2324 25
37
31
36
30
10
9
2122
35
8
7
34
17
29
1819
5
4
1516
33
28
32
27
3
2
AC309649
AB
D-24
Connector: D-24
<LHD>
D-24
8
3
1
4 5 6
2
7
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-16
After inspecting ABS-ECU connector B-03,
intermediate connectors C-104, C-117 and D-24, and
ABS sensor <rear: RH> connector D-13, inspect the
wire. If any of these connectors is damaged, repair or
replace it. Then go to Step 8.
Q: Is any harness wire between ABS-ECU connector
B-03 (terminals 11 and 17) and ABS sensor <rear:
RH> connector D-13 (terminals 1 and 2) damaged?
YES :
Repair it and then go to Step 8.
NO :
Go to Step 8.
STEP 8. Check whether the diagnosis code is
reset.
Q: Is diagnosis code No.11, 12, 13 or 14 set?
YES :
Start over at Step 1.
NO :
The procedure is complete.
AC308736
C-117
AJ
C-104(B)
Connectors: C-104, C-117
<RHD>
C-117
C-104(B)
15
1
8
3
10
2
9
11
4
13
12
5
14
16
7
6
38
1213
11
26
14
1
20
6
2324 25
37
31
36
30
10
9
2122
35
8
7
34
17
29
1819
5
4
1516
33
28
32
27
3
2
AC309650
AB
D-24
Connector: D-24
<RHD>
D-24
8
3
1
4 5 6
2
7
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-17
Code No.16: ABS-ECU Power Supply System (ABS-ECU Power Supply Voltage or Valve Relay Power
Supply Voltage below or above the Specified Value)
OPERATION
The ABS-ECU power is supplied to the ABS-ECU
(terminal 20) from the ignition switch (IG2) through
the multi-purpose fuse number 12 in the junction
block.
DIAGNOSIS CODE SET CONDITIONS
Output is provided when ABS-ECU power supply
voltage drops below or rises above the specified
value. Output is not provided if the power supply
voltage meets the specified voltage.
PROBABLE CAUSES
The most likely causes for this diagnosis code to set
are:
•
Malfunction of battery
•
Damaged wiring harness or connector
•
Malfunction of hydraulic unit and ABS-ECU
DIAGNOSIS
STEP 1. Check the battery.
Refer to GROUP 54A, Battery
−
On-vehicle Service
−
Q: Is the battery damaged?
YES :
Charge or replace the battery and then go
to Step 4.
NO :
Go to Step 2.
STEP 2. Check the charging system.
Refer to GROUP 16, Charging System
−
On-vehicles
Service
Q: Is the charging system damaged?
YES :
Repair the Charging System and then go to
Step 4.
NO :
Go to Step 3.
AC301687
ABS-ECU
IGNITION
SWITCH (IG2)
POWER
SOURCE
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
AB
ABS-ECU Power Supply Circuit
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-18
STEP 3. Check the harness wire between
junction block connector C-203 terminal 2 and
ABS-ECU connector B-03 terminal 20.
NOTE:
After inspecting ABS-ECU connector B-03,
intermediate connector C-106, and junction block
connector C-202 and C-203, inspect the wire. If any
of these connectors is damaged, repair or replace it.
Then go to Step 4.
AC301441AB
Connector: B-03
B-03 (GR)
Harness side
AC308721
C-203
AN
C-202
Connectors: C-202, C-203
<LHD>
C-202
Harness side
C-203
Harness side
10
1
6
14
5
12
13
4
11
7
2
3
8
9
4
6 5
3
2
1
AC308773
C-203
AO
C-202
Connectors: C-202, C-203
<RHD>
C-202
Harness side
C-203
Harness side
10
1
6
14
5
12
13
4
11
7
2
3
8
9
4
6 5
3
2
1
AC308718
C-106 (GR)
13
3
7
16
19
15
14
18
17
12
6
4
8
1
9
11
10
5
2
Connector: C-106
<LHD>
AS
AC308735
AX
C-106 (GR)
Connector: C-106
<RHD>
13
3
7
16
19
15
14
18
17
12
6
4
8
1
9
11
10
5
2
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст