Mitsubishi Outlander (2003+). Manual — part 518

INPUT SIGNAL PROCEDURES

SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR

54B-361

Step 6. Check the wiring harness between B-115
vehicles speed sensor connector terminal No.3
and C-219 ETACS-ECU connector terminal No.63.

NOTE:

AC308694

AC

B-115(B)

1

2

3

Connector: B-115 <2000>

Harness side

AC308708

AG

B-115(B)

1

2

3

Connector: B-115 <2400 (LHD)>

Harness side

AC308722

Connector: C-219

Junction block (Rear view)

AH

68

74

63

66

72

73

67

6564

61

70

71

62

69

60

57

58

59

5655

52

54 53

51

Harness side

C-219(GR)

<LHD>

AC308776

Connector: C-219 <RHD>

Junction block (Rear view)

AE

68

74

63

66

72

73

67

6564

61

70

71

62

69

60

57

58

59

5655

52

54 53

51

Harness side

C-219(GR)

AC308716

Connector: C-02
<LHD>

AF

2

1

3

13

12

14

21

10

5

4

6

16

15

17

7 8 9

19

18

20

11

22

C-02 (B)

AC308769

Connector: C-02 <RHD>

AG

2

1

3

13

12

14

21

10

5

4

6

16

15

17

7 8 9

19

18

20

11

22

C-02 (B)

AC308719

Connectors: C-16, C-105
<LHD>

10

1

21

16

13

4

11

2

12

3

1415

1718

5

20

7

19

6

8

22

9

C-16(L)

C-105

2

1

3

13

12

14

21

10

5

4

6

16

15

17

7 8 9

19

18

20

11

22

C-105

C-16

AB

INPUT SIGNAL PROCEDURES

SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR

54B-362

Prior to the wiring harness inspection, check joint
connector C-02, C-16 <2000> and intermediate
connector C-105, and repair if necessary.

•

Check the input line for open circuit.

Q: Is the check result normal?

YES :

Go to Step 7.

NO :

Repair the wiring harness.

Step 7. Retest the system.

Check that the vehicle speed signal is received
normally.

Q: Is the check result normal?

YES :

The trouble can be an intermittent

malfunction (Refer to GROUP 00

−

How to

Cope with Intermittent Malfunction

P.00-6

).

NO :

Replace the ETACS-ECU.

AC308736

Connectors: C-16, C-105
<RHD>

10

1

21

16

13

4

11

2

12

3

1415

1718

5

20

7

19

6

8

22

9

C-105

2

1

3

13

12

14

21

10

5

4

6

16

15

17

7 8 9

19

18

20

11

22

C-105

C-16

AB

C-16(L)

INPUT SIGNAL PROCEDURES

SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR

54B-363

INSPECTION PROCEDURE N-13: The vehicle speed signal is not received. <A/T>

CAUTION

Whenever the ECU is replaced, ensure that the
input signal circuit is normal.

COMMENTS ON TROUBLE SYMPTOM
Vehicle speed signal is used to operate the
windshield wiper (vehicle speed-dependent wiper
function). If this signal is abnormal, the windshield
wipers do not work normally.

POSSIBLE CAUSES

•

Malfunction of the engine-A/T-ECU

•

Malfunction of the ETACS-ECU

•

Damaged harness wires and connectors

ETACS-ECU

COMBINATION
METER

ENGINE-
A/T-ECU

Wire colour code
B : Black LG : Light green
G : Green L : Blue
W : White Y : Yellow
SB : Sky blue BR : Brown
O : Orange GR : Gray
R : Red P : Pink V : Violet

<LHD>

<RHD>

Vehicle Speed Sensor Input Circuit <A/T>

INPUT SIGNAL PROCEDURES

SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR

54B-364

DIAGNOSTIC PROCEDURE

Step 1. Check if the A/T related diagnosis code is
set.

Q: Is the diagnosis code set?

YES :

Diagnose the automatic transmission

control system. (Refer to GROUP 23

−

Troubleshooting

P.23A-18

)

NO :

Go to Step 2.

Step 2. Connector check: C-141 engine-A/T-ECU
connector and C-219 ETACS-ECU connector

Q: Is the check result normal?

YES :

Go to Step 3.

NO :

Repair the defective connector.

AC308718

AE

Connector: C-141 <LHD>

C-141(GR)

Harness side

AC308735

AD

Connector: C-141 <RHD>

C-141(GR)

Harness side

AC308722

Connector: C-219

Junction block (Rear view)

AH

68

74

63

66

72

73

67

6564

61

70

71

62

69

60

57

58

59

5655

52

54 53

51

Harness side

C-219(GR)

<LHD>

AC308776

Connector: C-219 <RHD>

Junction block (Rear view)

AE

68

74

63

66

72

73

67

6564

61

70

71

62

69

60

57

58

59

5655

52

54 53

51

Harness side

C-219(GR)