Mitsubishi Outlander (2003+). Manual — part 216
ON-VEHICLE SERVICE
AUTOMATIC TRANSMISSION (FF)
23A-159
KEY INTERLOCK AND SHIFT LOCK
MECHANISM CHECK
M1232003100238
1. Carry out the following check.
2. If the above operations do not occur correctly,
adjust the shift lock cable unit by the following
procedure.
(1) Remove the front floor console (Refer to
GROUP 52A
−
Floor Console Assembly
) <LHD>.
Remove the instrument panel center console
(Refer to GROUP 52A
−
Instrument Panel
) <RHD>.
(2) Move the selector lever to P position.
(3) Turn the ignition key to LOCK (OFF) position.
Key interlock side
Inspection
procedure
Inspection conditions
Check details (normal condition)
1
Brake pedal:
Depressed
Ignition key position:
LOCK (OFF) or pulled out
The selector lever push button cannot be
pushed, and the selector lever should not
be moved from P position.
2
Ignition key position:
Other than above
The selector lever push button can be
pushed, and the selector lever can be
moved from P position.
3
Selector lever position: Other than P position
The ignition key cannot turned to LOCK
(OFF) position.
4
Selector lever position: P position
The ignition key can be turned to LOCK
(OFF) position.
shift lock side
Inspection
procedure
Inspection conditions
Check details (normal condition)
1
Ignition switch
position: ACC
Brake pedal:
Depressed
The selector lever push button can be pushed, and the
selector lever can be moved from P position.
2
Brake pedal:
Not depressed
The selector lever push button cannot be pushed, and
the selector lever should not be moved from P position.
3
The selector lever push button can be pushed, and the
selector lever can be moved from R position to P
position.
AC000004
B
C
A
View A
Lock guide
AC
Lock released
Locked
Key interlock cable
Cap
Lever
Shift lock cable
Shift lock
cable unit
Fixing bolt
ON-VEHICLE SERVICE
AUTOMATIC TRANSMISSION (FF)
23A-160
(4) Loosen the shift lock cable unit fixing bolt, and
then while pushing the lever in direction of B
and the unit in direction of C, tighten the fixing
bolt to the specified torque.
Tightening torque: 12
±
2 N
⋅
m
(5) Lift the lock guide to unlock the key
interlocking cable.
(6) While pushing the cap of the key interlock
cable in the direction of B, lower the lock guide
to lock the cable.
NOTE: The lock position at this time (the
amount by which the cap is pushed) represents
the amount of adjustment for the key interlock
cable. If the key interlock cable does not
operate correctly, adjust the lock position.
3. After adjusting, check the operation once more. If
the operation is still incorrect, replace the shift
lock unit. (Refer to
<vehicles with
LHD> or
<vehicles with RHD>)
TRANSMISSION CONTROL
AUTOMATIC TRANSMISSION (FF)
23A-161
TRANSMISSION CONTROL
REMOVAL AND INSTALLATION
<VEHICES WITH LHD>
M1231006600400
CAUTION
When removing and installing the transmission control cable and shift lock cable unit, be careful not
to hit the SRS-ECU.
Pre-removal and Post-installation Operation
•
Front Floor Console Removal. (Refer to GROUP 52A
−
Floor Console Assembly
.)
AC300157AC
5.0 ± 1.0 N·m
2
4
12 ± 2 N·m
12 ± 2 N·m
1
6
5
3
12 ± 2 N·m
Transmission control cable
assembly removal steps
•
Air cleaner assembly (Refer to
GROUP 15
.)
•
Battery and battery tray
>>B<<
1.
Transmission control cable
assembly connection
(transmission side)
>>A<<
2.
Shift lock cable unit connection
3.
Transmission control cable
assembly connection (selector
lever assembly side)
4.
Harness connector
5.
Selector lever assembly
•
SRS-ECU (Refer to GROUP 52B,
SRS control unit
.)
6.
Transmission control cable
assembly
Selector lever assembly
removal steps
>>A<<
2.
Shift lock cable unit connection
3.
Transmission control cable
assembly connection (selector
lever assembly side)
4.
Harness connector
5.
Selector lever assembly
Transmission control cable
assembly removal steps
TRANSMISSION CONTROL
AUTOMATIC TRANSMISSION (FF)
23A-162
INSTALLATION SERVICE POINTS
>>A<< SHIFT LOCK CABLE UNIT INSTALLATION
1. Selector lever to P position.
2. Turn the ignition key to LOCK (OFF) position.
3. Install the shift lock cable unit rod to the selector
lever assembly lock cam, and tighten the shift lock
cable unit installation bolt to the specified torque.
Tightening torque: 5.0
±
1.0 N
⋅
m
4. Check the selector lever operation. (Refer to
>>B<< TRANSMISSION CONTROL CABLE
(TRANSMISSION SIDE) INSTALLATION
1. Place the selector lever and manual control lever
in the N position.
2. Place the cable stud into the manual control lever
slot and install the nut loosely. Gently push the
transmission control cable into the manual control
lever slot until the cable is taut. Tighten the nut to
the specified torque.
Tightening torque: 12
±
2 N
⋅
m
AC203163AC
Lock cam
Shift lock
cable unit
AC103395AO
Manual control lever
Adjusting nut
12 ± 2 N·m
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст