Mitsubishi Outlander (2003+). Manual — part 275

TROUBLESHOOTING

ANTI-SKID BRAKING SYSTEM (ABS)

35B-43

STEP 2. Check the harness wire between
junction block connector C-202 terminal 8 and
ABS-ECU connector B-03 terminal 20.

NOTE:

After inspecting ABS-ECU connector B-03, junction
block connector C-202 and intermediate connector
C-106, inspect the wire. If any of these connectors is
damaged, repair or replace it. Then go to Step 5.

Q: Is the harness wire between junction block

connector C-202 terminal 8 and ABS-ECU
connector B-03 terminal 20 damaged?

YES :

Repair it and go to Step 5.

NO :

This malfunction is intermittent. Refer to
GROUP 00, How to Use
Troubleshooting/Inspection Service Points

−

How to Cope With Intermittent Malfunction

P.00-6

.

AC301441AB

Connector: B-03

B-03 (GR)

Harness side

AC308720

C-202

Harness side

10

1

6

14

5

12

13

4

11

7

2

3

8

9

AM

Connector: C-202
<LHD>

AC308772

C-202

Harness side

10

1

6

14

5

12

13

4

11

7

2

3

8

9

Connector: C-202
<RHD>

AL

AC308718

C-106 (GR)

13

3

7

16

19

15

14

18

17

12

6

4

8

1

9

11

10

5

2

Connector: C-106
<LHD>

AS

AC308735

AX

C-106 (GR)

Connector: C-106
<RHD>

13

3

7

16

19

15

14

18

17

12

6

4

8

1

9

11

10

5

2

TROUBLESHOOTING

ANTI-SKID BRAKING SYSTEM (ABS)

35B-44

STEP 3. Check the harness wires between
ABS-ECU connector B-03 (terminals 4 and 13)
and diagnosis connector C-24 (terminals 1 and
7).

AC301441AB

Connector: B-03

B-03 (GR)

Harness side

AC308717

Connectors: C-02, C-24 <LHD>

C-24(B)

C-24 Harness side

AT

C-02

C-02

AC308770

AH

Connectors: C-02, C-24 <RHD>

C-02

33

22

11

28

17

16

15

14

13

12

25

2324

2627

3

1 2

4 5

21

20

19

18

2930

32

31

7

6

8

10

9

C-02

C-24(B)

C-24 Harness side

TROUBLESHOOTING

ANTI-SKID BRAKING SYSTEM (ABS)

35B-45

NOTE:

After inspecting ABS-ECU connector B-03, diagnosis
connector C-24, and intermediate connectors C-02,
C-104 and C-105, inspect the wires. If any of these
connectors is damaged, repair or replace it. Then go
to Step 5.

Q: Is any of the harness wires between ABS-ECU

connector B-03 (terminals 4 and 13) and diagnosis
connector C-24 (terminals 1 and 7) damaged?

YES :

Repair it and go to Step 5.

NO :

Go to Step 4.

STEP 4. Check the harness wires between
ABS-ECU connector B-03 (terminals 2 and 18)
and earth (No.9).

Q: Is any of the harness wires between ABS-ECU

connector B-03 (terminals 2 and 18) and earth
(No.9) damaged?

YES :

Repair it and then go to Step 5.

NO :

Check the troubleshooting condition. To
reproduce the troubleshooting state replace
the hydraulic unit (integrated with
ABS-ECU).Then go to Step 5. If the state of
failure is not reproduced then a intermittent
malfunction is suspected. Refer to GROUP
00, How to Use Troubleshooting/Inspection
Service Points

−

How to Cope with

Intermittent Malfunction

P.00-6

.

AC308719

C-105

AK

Connectors: C-104, C-105
<LHD>

C-104(B)

C-105

C-104(B)

10

1

21

16

13

4

11

2

12

3

1415

1718

5

20

7

19

6

8

22

9

15

1
8

3

10

2
9

11

4

13

12

5

14

16

7

6

AC308736

C-105

AI

C-104(B)

Connectors: C-104, C-105
<RHD>

C-105

C-104(B)

15

1
8

3

10

2
9

11

4

13

12

5

14

16

7

6

10

1

21

16

13

4

11

2

12

3

1415

1718

5

20

7

19

6

8

22

9

AC301441AB

Connector: B-03

B-03 (GR)

Harness side

AC208089AC

Relay box

Earth (No.9)

TROUBLESHOOTING

ANTI-SKID BRAKING SYSTEM (ABS)

35B-46

STEP 5. Retest the system.

Q: Does the MUT-II/III communicate with the ABS

system?

YES :

The procedure is complete.

NO :

Start over at Step 1.

INSPECTION PROCEDURE 2: When the Ignition Key is Turned to the "ON" position (Engine Stopped),
the ABS Warning Lamp does not Illuminate.

OPERATION

•

The ABS warning lamp is lit up by transistor
control in the ABS-ECU. However, the
relationship of the reverse circuit movement in
the combination meter will vary from usual in
terms of transistor ON/OFF and ABS warning
lamp ON/OFF, in that the ABS warning lamp will

lamp up when the transistor is turned OFF for this
circuit. This is how the ABS warning lamp lights
up even when the ABS-ECU connector is
connected improperly or if the ABS-ECU function
has terminated.

•

The ABS-ECU also lights up the ABS warning
lamp during the initial check (approximately 3
seconds) when the ignition switch is turned to the
"ON" position in addition to when the system is
malfunctioning.

ABS-ECU

IGNITION
SWITCH (IG1)

COMBINATION
METER

<LHD>

CPU

<RHD>

<LHD>

<RHD>

Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet

ABS Warning Lamp Circuit