Mitsubishi Outlander (2003+). Manual — part 336
WIPER DEICER
EXTERIOR
51-43
WIPER DEICER
INSPECTION
M1511019100619
WIPER DEICER CHECK
There should be continuity between the wiper deicer
connector terminal No.1 and 2.
WIPER DEICER RELAY CHECK
1 2
AC301953
Windshield wiper motor
Windshield
AB
Battery voltage Terminal
number to be
connected to
tester
Continuity test
results
Not applied
1
−
4
Open circuit
Connect
terminal No.3
and battery (
−
)
terminal.
Connect
terminal No.2
and battery (+)
terminal.
1
−
4
Less than 2
ohms
AC211776
3
4
1
2
1 2
3 4
AC301954 AB
Wiper deicer relay
HEADLAMP WASHER
EXTERIOR
51-44
HEADLAMP WASHER
TROUBLESHOOTING
M1511000700486
The headlamp washer is controlled by the Smart
Wiring System (SWS). For troubleshooting, refer to
GROUP 54B, Troubleshooting
or GROUP
54C, Troubleshooting
HEADLAMP WASHER
REMOVAL AND INSTALLATION
M1511009700041
Pre-removal and Post-installation Operation
•
Radiator Grille Removal and Installation (Refer to
•
Front Bumper Extension Removal and Installation (Refer
to
).
•
Under Cover Removal and Installation (Refer to
).
AC300298
1
2
3
4
5
6
7
8
9
10
8
9
10
11
12
11
12
13
14
15
N
N
AB
Removal steps
•
Washer fluid draining
1.
Headlamp washer hose connection
2.
Headlamp washer motor connector
3.
Headlamp washer hose
4.
Headlamp washer joint
5.
Headlamp washer hose
6.
Headlamp washer motor
7.
Headlamp washer motor packing
•
Front bumper (Refer to
).
8.
Headlamp washer cover
Removal steps (Continued)
MARK
EXTERIOR
51-45
INSPECTION
M1511009800060
HEADLAMP WASHER MOTOR CHECK
1. Remove the headlamp washer motor connector.
2. Check to see that the water is vigorously sprayed
when connecting the positive battery terminal to
terminal number 1 and terminal number 2 to the
negative battery terminal.
MARK
REMOVAL AND INSTALLATION
M1511011800603
9.
Headlamp washer nozzle
10. O-ring
11. Headlamp washer actuator
assembly
12. Headlamp washer hose
13. Headlamp washer joint
14. Headlamp washer hose
15. Headlamp washer joint
Removal steps (Continued)
AC300406
1 2
AB
AC300472
1
2
3
AC
1. Front three-diamond mark
>>A<<
2. Rear three-diamond mark
>>A<<
3. OUTLANDER mark and 4WD mark
MARK
EXTERIOR
51-46
INSTALLATION SERVICE POINT
>>A<< MARK INSTALLATION
1. Clean the mark installation surfaces on the body
with unleaded petrol.
CAUTION
When attaching the marks, the ambient
temperature should be 20
−
38
°
C and the air
should be completely free of dust. If the ambient
temperature is lower than 20
°
C, the marks and
the places on the vehicle body where the marks
are to be attached should be heated to 20
−
38
°
C.
2. Peel off the protection sheet on the back of the
mark to paste it on the installation position.
AC309427
Centre line
of vehicle
Press line
Units: mm
AB
66 ± 1
Three-diamond mark
AC309426
AB
50
OUTLANDER mark and 4WD mark
Tailgate panel end line
Units: mm
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст