Mitsubishi Outlander (2003+). Manual — part 180
TROUBLESHOOTING <A/T>
AUTOMATIC TRANSMISSION (FF)
23A-15
SHIFT PATTERN
M1231028400192
UPSHIFT PATTERN
9
Selector lever
position: N
(Must be done
on a level and
straight road)
Selector lever
position and vehicle
speed
(1) Select R and
drive at 10 km/h
The ration of data list
No.22 and No.23
should be the same
as the transmission
ratio when reversing
No shifting 22
Input shaft
speed
sensor
system
23
Output
shaft speed
sensor
system
46
Reverse
without
completion
of shifting
Procedure Pre-test/operation
conditions
Test/operation
Judgment value
Check item
Diagnosis
code No.
Inspection
procedure if
there is an
abnormality
AC309445
100
50
0
4.5
4.0
3.0
0.5
1.0
2.0
1,000
2,000
3,000
4,000
5,000
6,000
7,000
100
50
0
150
200
Throttle
opening
voltage (V)
Throttle
Opening (%)
1
2
2
3
3
4
2 3
movement
range
3 4
movement
range
Output shaft speed r/min
Vehicle speed km/h
8,000
AB
TROUBLESHOOTING <A/T>
AUTOMATIC TRANSMISSION (FF)
23A-16
DOWNSHIFT PATTERN
DAMPER CLUTCH CONTROL
M1231021300064
In 4th range
AC309446AB
100
50
0
1,000
2,000
4,000
5,000
3,000
6,000
7,000
100
50
0
150
200
4.5
4.0
3.0
2.0
1.0
0.5
Throttle
opening
voltage (V)
Throttle
opening (%)
Output shaft speed r/min
Vehicle speed km/h
1
2
2
3
3
4
2
3
(Sport mode)
3
4
(Sport mode)
1
3
(Sport mode)
AC309497 AC
4.5
4.0
3.0
2.0
1.0
0.5
100
50
0
1,000
2,000
3,000
4,000
5,000
6,000
7,000
0
50
100
150
Damper clutch
disengaged
Damper clutch engaged
Throttle
opening
voltage (V)
Throttle
opening (%)
Output shaft speed r/min
Vehicle speed km/h
TROUBLESHOOTING <A/T>
AUTOMATIC TRANSMISSION (FF)
23A-17
In 3rd range
AC309498AB
4.5
4.0
3.0
2.0
1.0
0.5
100
50
0
1,000
2,000
3,000
4,000
5,000
6,000
7,000
0
50
100
150
Damper clutch disengaged
Damper clutch engaged
Throttle
opening
voltage (V)
Throttle
opening (%)
Output shaft speed r/min
Vehicle speed km/h
TROUBLESHOOTING <A/T>
AUTOMATIC TRANSMISSION (FF)
23A-18
INSPECTION CHART FOR DIAGNOSIS
CODE
M1231007900385
NOTE: The MPI diagnostic trouble codes are the codes which are set when item "MPI" is selected on
MUT-II/III. However, the codes above indicate failure in the automatic transmission.
A/T
diagnosis
code No.
MPI
diagnosis
code No.
Diagnosis item
Reference page
15
P0710
A/T fluid temperature sensor system
16
21
−
Crank angle sensor system
Refer to GROUP
13B,
Troubleshooting
22
P0715
Input shaft speed sensor system
23
P0720
Output shaft speed sensor system
26
−
Stop lamp switch system
27
P0705
Inhibitor switch system
28
31
P0750
LR solenoid valve system
32
P0755
UD solenoid valve system
33
P0760
2ND solenoid valve system
34
P0765
OD solenoid valve system
36
P0740
DCC solenoid valve system
41
−
1st gear ratio does not meet the specification
42
−
2nd gear ratio does not meet the specification
43
−
3rd gear ratio does not meet the specification
44
−
4th gear ratio does not meet the specification
46
−
Reverse gear ratio does not meet the specification
52
−
DCC solenoid valve system
54
P1751
A/T control relay system
56
−
N range lamp system
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст