Mitsubishi Outlander (2003+). Manual — part 243
GENERAL INFORMATION
POWER PLANT MOUNT
32-3
AC309245
AC309246
AC309368
Centremember
Engine rear roll
stopper bracket
Engine roll stopper
rod bracket
Engine roll stopper
rod assembly
Engine roll stopper
bracket
Transmission mounting
body side bracket
<M/T>
<A/T-L.H. drive vehicles>
AC
<4G69>
Engine front mounting
bracket
<M/T>
<A/T>
<M/T>
<A/T>
<A/T-R.H. drive vehicles>
<M/T>
<A/T>
Engine roll stopper
rod assembly
Engine roll stopper
rod bracket
Engine roll stopper
bracket
Engine front mounting
bracket
Transmission mounting
body side bracket
SERVICE SPECIFICATION
POWER PLANT MOUNT
32-4
SERVICE SPECIFICATION
M1321000300377
SPECIAL TOOL
M1321000600420
Item
Standard value
Protruding length of stabilizer link thread part mm
9.4
±
0.4
Tool
Number
Name
Use
MB991897
Ball joint remover
Knuckle and tie rod end ball joint
disconnection
NOTE: Steering linkage puller
(MB990635 or MB991113) is also
available to disconnect knuckle and
tie rod end ball joint.
AC106827
ENGINE MOUNTING
POWER PLANT MOUNT
32-5
ENGINE MOUNTING
REMOVAL AND INSTALLATION
M1321001100547
CAUTION
*: Indicates parts which should be initially tightened, and then fully tightened after placing the vehicle
horizontally and loading the full weight of the engine on the vehicle body.
INSTALLATION SERVICE POINT
>>A<< SELF-LOCKING NUT INSTALLATION
CAUTION
Do not tighten the self-locking nuts while the
engine is hot.
Tighten the self-locking nuts to the specified torque
while the engine is cold.
Tightening torque: 70
±
4 N
⋅
m
INSPECTION
M1321001200209
•
Check the engine front mounting bracket for
cracks or damage.
Pre-removal Operation
•
Raise the engine and transmission assembly until its
weight is not applied to the insulator, and support it
securely.
•
Accelerator Pedal Position Sensor Removal (Refer to
GROUP 17, Accelerator Pedal Position Sensor
<4G69>.
Post-installation Operation
•
Accelerator Pedal Position Sensor Installation (Refer to
GROUP 17, Accelerator Pedal Position Sensor
<4G69>.
•
Accelerator Cable Check and Adjustment (Refer to
GROUP 17, On-vehicle Service
) <4G69>.
AC309430
AC309429
AC309428
1
3
44 ± 10 N·m
44 ± 10 N·m
45 ± 5 N·m
12 ± 2 N·m
N
AB
1
3
44 ± 10 N·m
44 ± 10 N·m
70 ± 4 N·m
12 ± 2 N·m
N
<M/T>
<A/T>
2
2
Removal steps
1.
Pressure hose clamp
>>A<<
2.
Self-locking nut
3.
Engine front mounting bracket
TRANSMISSION MOUNTING <M/T>
POWER PLANT MOUNT
32-6
TRANSMISSION MOUNTING <M/T>
REMOVAL AND INSTALLATION
M1321001400485
CAUTION
*: Indicates parts which should be initially tightened, and then fully tightened after placing the vehicle
horizontally and loading the full weight of the engine on the vehicle body.
Pre-removal Operation
•
Raise the engine and transmission assembly until its
weight is not applied to the insulator, and support it
securely.
•
Air Cleaner Removal (4G63: Refer to GROUP 15, Air
Cleaner
), (4G69: Refer to GROUP 15, Air Cleaner
).
•
Centremember and Engine Roll Stopper Bracket Removal
<4G63-2WD> (Refer to
•
Engine Rear Roll Stopper rod assembly or Engine Rear
Roll Stopper Bracket Removal <4G63-4WD> (Refer to
•
Engine Rear Roll Stopper rod assembly or Engine Rear
Roll Stopper Bracket Removal <4G69-L.H. drive
vehicles> (Refer to
).
Post-installation Operation
•
Engine Rear Roll Stopper rod assembly or Engine Rear
Roll Stopper Bracket Installation <4G63-4WD> (Refer to
•
Engine Rear Roll Stopper rod assembly or Engine Rear
Roll Stopper Bracket Installation <4G69-L.H. drive
vehicles> (Refer to
•
Centremember and Engine Roll Stopper Bracket
Installation <4G63-2WD> (Refer to
•
Air Cleaner Installation (4G63: Refer to GROUP 15, Air
), (4G69: Refer to GROUP 15, Air Cleaner
).
AC301677
47 ± 7 N·m
82 ± 7 N·m
2
2
1
AB
Removal steps
1.
Transmission mounting body side
bracket
>>A<<
2.
Transmission mounting stopper
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст