Mitsubishi Outlander (2003+). Manual — part 526

ON-VEHICLE SERVICE

SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR

54B-393

ON-VEHICLE SERVICE

ADJUSTMENT FUNCTION <Vehicles with
keyless entry system>

M1549002500593

According to the adjustmentmode entry conditions of
the input switch, the following functions can be
adjusted. The data on adjustment will be memorized
even if the battery is removed.

•

Keyless entry system hazard answerback
function

•

Vehicle speed-dependent wiper function

•

Headlamp automatic-shutdown function

•

Dimmer interior lamp control

•

Interior lamp automatic-shutdown function

•

Initialization of all functions (Returns to initial
settings)

1. Conditions for entering the adjustment mode

i. Set each switch to the following state.

•

Hazard lamp switch: OFF

•

Diagnosis control: ON (Connect the
MUT-II/III or earth No.1 pin of the 16-pin
diagnosis connector.)

•

Key reminder switch: OFF (Insert the
ignition key)

•

Ignition switch: "LOCK" (OFF) position

•

Driver's door switch: OFF (driver's door
closed)

ii. When the windshield washer switch is ON for

more than ten seconds, the buzzer in the
ETACS-ECU sounds for three seconds, and
the adjustment mode will be set.

2. Conditions for exiting the adjustment mode

•

Diagnosis control: OFF (Disconnect the
MUT-II/III or the earth of No.1 pin of the 16-pin
diagnosis connector disconnected.)

•

Key reminder switch: ON (Remove the
ignition key)

•

Ignition switch: Turning to any position other
than "LOCK" (OFF) position

•

Driver's door switch: ON (driver's door
opened)

•

When three minutes pass without
configurations performed

•

When the other warning buzzer output is
generated

3. Configurations of various functions

Function

Adjustment procedure

Keyless entry system hazard
answerback function

When the lock button of the transmitter is pressed twice continuously within
two seconds, the hazard answerback function during the lock state will be
switched between available or unavailable.

•

Function available: Buzzer sounds once. (Initial state)

•

Function not available: Buzzer sounds twice.

When the unlock button of the transmitter is pressed twice continuously
within two seconds, the hazard answerback function during the unlock
state will be switched between available or unavailable.

•

Function available: Buzzer sounds once. (Initial state)

•

Function not available: Buzzer sounds twice.

Vehicle speed-dependent
wiper function

When the windshield wiper mist switch is turned ON for more than two
seconds, the vehicle speed-dependent wiper function is switched between
available or unavailable.

•

Function available: Buzzer sounds once. (Initial state)

•

Function not available: Buzzer sounds twice.

Headlamp
automatic-shutdown function

When the passing switch is turned ON for more than two seconds with the
head lamp switch ON and the turn signal lamp switch turned to RH, the
headlamp automatic-shutdown function is switched between available or
unavailable.

•

Function not available: Buzzer sounds twice.

•

Function available: (when the tail lamp illuminates with the ignition
switch turned to the "LOCK" (OFF) position, it is not automatically turned
off): Buzzer sounds three times. (Initial state)

ON-VEHICLE SERVICE

SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR

54B-394

Dimmer interior lamp control

When the turn signal lamp switch is set in the order of RH to LH to RH to
LH within three seconds from the LH position, the delayed lamp-off time
switches (Returns to a after e, and repeats from a in order.)

a. 30 seconds: Buzzer sounds once.
b. 10 seconds: Buzzer sounds twice.
c. 0 seconds (No delay time): Buzzer sounds three times.
d. 15 seconds: Buzzer sounds four times. (Initial state)
e. 7.5 seconds: Buzzer sounds five times.

Interior lamp
automatic-shutdown function

When the hazard lamp switch is turned ON for more than two seconds, the
interior lamp automatic-shutdown function switches in the following order.
(a and b switches alternately)

a. Function available: Buzzer sounds once. (Initial state)
b. Function not available: Buzzer sounds twice.

Initialization of all functions

When the windshield washer switch is ON for more than 20 seconds
continuously, the buzzer sounds twice, and all functions will be initialized.
(Settings are returned to their initial states.) The adjustment mode entry
buzzer sounds after 10 seconds, however to initialize all functions, the ON
state should be continued for 20 seconds. When the windshield washer
switch is ON for more than 20 seconds continuously without the adjustment
mode set, the adjustment mode will be set after 10 seconds without the
initialization of all functions.

Function

Adjustment procedure