Mitsubishi Outlander (2003+). Manual — part 408
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-27
Registration of additional keys with the MUT-II
Additional key(s) can be registered with the MUT-II
while keeping all existing key data.
CAUTION
To prevent damage to MUT-II, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting MUT-II.
NOTE: To register additional keys with the MUT-II,
no registered keys must be lost.
1. Connect MUT-II (MB991502) to the 16-pin
diagnosis connector.
2. Turn the ignition switch to "ON" position.
3. At "System Select," press "YES"
4. Select "Immobilizer," press "YES".
5. Select "Special Func", press "YES". If diagnosis
code No.11 exists, "Can't execute" will be
displayed. Check for diagnosis code No.11 (Refer
to
6. Select "Add key ID reg", press "YES".
7. Press the "YES" key to start key ID registration.
AC300830
Steering shaft
MUT-II
AB
AC000522AD
AC000523AC
AC000530AC
AC000518AC
AC101478
AB
AC101477
AB
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-28
8. This will be displayed when the add key ID
registration is successful. If an error occurs during
key ID registration, the message "Can't execute"
will be displayed. If the key has already been
registered, "Key ID has been registered" will be
displayed.
9. The number of keys currently registered will be
displayed. To register an additional key, replace
the ignition key with the next key to be registered
within five seconds and then press the "YES" key.
Key ID registration screen will be displayed, then
register another key.
NOTE: A maximum of eight different keys can be
registered.
10.If key ID registration is complete, press the "NO"
key.
11.This completes the registration operation. Turn
the ignition switch "LOCK" (OFF) and leave it off
for approximately ten seconds.
12.Check that the engine can be started with each of
the ignition keys.
13.Check that the immobilizer system diagnosis
code and MPI system diagnosis code did not set.
14.Turn the ignition switch to "LOCK" (OFF) position.
15.Disconnect MUT-II.
KEY ID (ENCRYPTED CODE)
REGISTRATION <MUT-III>
All ignition keys can be registered with MUT-III.
Additional ignition keys can be registered with
MUT-III.
Registration with the MUT-III
CAUTION
To prevent damage to MUT-III, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting MUT-III.
NOTE:
.
•
Before registration, check that no diagnosis code
is set. If a diagnosis code is set, resolve the
problem beforehand.
•
Using the key ID register function will cause all
key IDs that have been previously registered in
the immobilizer-ECU to be erased. All keys need
to be registered. Those which have been
registered before should be on hand before using
this function.
•
If registering more than one key, do not
disconnect MUT-III halfway through the
registration process.
•
After registering key IDs, check that the engine
can be started using all of the keys that have
been registered. If the engine will not start, refer
to Immobilizer System Diagnosis
.
1. Connect the MUT-III to the diagnosis connector
(16-pin).
2. Turn the ignition switch to "ON" position.
AC101476
AB
AC308915AB
MB991911
16-PIN
MB991827
MB991824
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-29
3. Select "System select" from the start-up screen.
4. Choose "IMMOBILIZER" from the "POWER
TRAIN" tab.
5. Choose "Special Function" from "IMMOBILIZER"
screen.
6. Choose "Key registration" from "Special Function"
screen.
7. Enter the vehicle’s password (secret code) on the
"Key registration" screen, and then click the check
mark icon. Follow the prompts on the screen to
insert key(s) into the ignition switch to begin key
registration.
8. If the key ID was registered successfully,
"Progress" indication will turn active (gray). Then
the registration process completes. If the key ID
failed to be registered, "In-Complete" indication
will turn active (gray).
9. The number of keys currently registered will be
displayed. To register an additional key, replace
the ignition key with the next key to be registered
within five seconds. Key ID registration screen will
be displayed, then register another key.
NOTE: A maximum of eight different keys can be
registered.
10.This completes the registration operation. Turn
the ignition switch "LOCK" (OFF) and leave it off
for approximately ten seconds.
11.Check that the engine can be started with each of
the ignition keys.
12.Check that the immobilizer system diagnosis
code and MPI system diagnosis code did not set.
13.If not diagnosis code is shown, terminate the
MUT-III.
14.Turn the ignition switch to "LOCK" (OFF) position.
15.Disconnect MUT-III.
System select
Special function
CAN bus diagnosis
Function Select Menu
Menu
AC209666
Maintenance
AD
MPI/GDI/DIESEL
ELC-A/T/CVT
IMMOBILIZER
SS4II
TCL/STARLTY CONTROL
AUTO CRUISE
CHASSIS
BODY
System Select Menu
POWER TRAIN
AC305175
Check Chart For
Problem Sy
Data List
Special
Function
Self-diagnosis
Simulated Vehicle
Speed Out
Resistor
Voltmeter
POWERTRAIN
IMMOBILIZER
IMMOBILIZER
AC305176
Key ID registration
Additional Key
Registration
POWERTRAIN
Special Function
IMMOBILIZER
Special Function
AC305177
POWERTRAIN
IMMOBILIZER
Special Function
7
8
9
4
5
6
1
2
3
0
Back
Space
Clear
Key registration
AC207300
AD
POWERTRAIN
IMMOBILIZER
Special Function
IMMOBILIZER-ECU registration
Progress
In-Complete
Key registration
AC207302
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-30
Registration of additional keys with the MUT-III
Additional key(s) can be registered with the MUT-III
while keeping all existing key data.
CAUTION
To prevent damage to MUT-III, always turn the
ignition switch to "LOCK" (OFF) position before
connecting or disconnecting MUT-III.
NOTE: To register additional keys with the MUT-III,
no registered keys must be lost.
1. Connect MUT-III to the 16-pin diagnosis
connector.
2. Turn the ignition switch to "ON" position.
NOTE: Before registration, check that no diagnosis
code is set. If a diagnosis code is set, resolve the
problem beforehand.
3. Carry out steps 3 to 6 of the sub-section
"Registration with MUT-III."
4. Choose "Transponder ID addition" from "Special
Function" screen.
5. Enter the vehicles password (secret code) on the
"Transponder ID addition" screen, and then click
the check mark icon.
6. If an additional registration is made successfully,
the screen will ask if another key is registered or
not. If the third ignition key is registered, remove
the key, which has been registered. Then insert
the third key within five seconds, and then turn it
to the ON position.
7. Register the additional ignition key according to
step 6 above. The number of the registered
ignition keys are shown on "The number of
registered key" screen.
NOTE: A maximum of eight different keys can be
registered.
8. This completes the registration operation. Turn
the ignition switch "LOCK" (OFF) and leave it off
for approximately ten seconds.
9. Check that the engine can be started with each of
the ignition keys.
10.Check that the immobilizer system diagnosis
code and MPI system diagnosis code did not set.
11.If not diagnosis code is shown, terminate the
MUT-III.
12.Turn the ignition switch to "LOCK" (OFF) position.
13.Disconnect MUT-III.
AC308915AB
MB991911
16-PIN
MB991827
MB991824
Key ID registration
Additional Key
Registration
POWERTRAIN
Special Function
IMMOBILIZER
Special Function
AC305177
POWERTRAIN
IMMOBILIZER
Password
Special Function
7
8
9
4
5
6
1
2
3
0
Back
Space
Clear
Trasponder ID addition
AC207301
AC207301
AC209775
POWERTRAIN
IMMOBILIZER
Key ID register
The number of registered key
3
Progre
Special Function
Trasponder ID addition
About Additional Transponder
ID SET
If register another key ID, press the
OK button after inserting a new key
within 5 sec and turning on IG-SW.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст