Mitsubishi Outlander (2003+). Manual — part 508
INPUT SIGNAL PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-321
DIAGNOSTIC PROCEDURE
Step 1. Use the MUT-II/III to confirm a diagnosis
code.
Check that the ETACS-ECU sets a diagnosis code.
Q: Is the diagnosis code set?
YES :
Refer to diagnosis code chart
NO :
Go to Step 2.
Step 2. Retest the system.
Replace the column switch, and check if the column
switch (windshield wiper washer and rear wiper
washer switch) sends signal.
(1) Replace the column switch.
(2) Check if the column switch (windshield
wiper/washer and rear wiper washer switch)
sends signal.
Q: Is the check result normal?
YES :
The procedure is complete.
NO :
Replace the ETACS-ECU.
INSPECTION PROCEDURE N-7: The windshield intermittent wiper volume signal is not received.
CAUTION
Whenever the ECU is replaced, ensure that the
input signal circuit is normal.
COMMENTS ON TROUBLE SYMPTOM
The intermittent wiper interval is calculated in
accordance with the input signal from the windshield
intermittent wiper volume. If this signal is abnormal,
the wiper interval can not be adjusted.
POSSIBLE CAUSES
•
Malfunction of the column switch
•
Malfunction of the ETACS-ECU
•
Damaged harness wires and connectors
COLUMN
SWITCH
WINDSHIELD
INTERMITTENT
WIPER INTERVAL
ADJUSTING KNOB
UPPER
SIDE
ETACS-
ECU
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Windshield Intermittent Wiper Interval Adjusting Knob Input Circuit
INPUT SIGNAL PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-322
DIAGNOSTIC PROCEDURE
Step 1. Connector check: C-310 column switch
connector
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the defective connector.
Step 2. Measure the resistance at the C-310
column switch connector.
(1) Disconnect the connector, and measure at the
column switch side.
(2) Resistance between C-310 column switch
connector terminal No.6 and body earth
OK: The resistance should rise from 0 to
1 k
Ω
when the windshield intermittent
wiper volume is rotated from "Fast" to
"Slow".
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Replace the column switch.
AC308724
Connector: C-310
AB
Harness side
10
5
6
7
9 8
3
4
2 1
<LHD>
AC308778
Connector: C-310
AB
Harness side
10
5
6
7
9 8
3
4
2 1
<RHD>
AC308724
Connector: C-310
AB
Harness side
10
5
6
7
9 8
3
4
2 1
<LHD>
AC308778
Connector: C-310
AB
Harness side
10
5
6
7
9 8
3
4
2 1
<RHD>
AC301541BC
Connector C-310
(Harness side)
10
5
6
7
9 8
3
4
2 1
INPUT SIGNAL PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-323
Step 3. Connector check: C-219 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the defective connector.
Step 4. Check the wiring harness between C-310
column switch connector terminal No.6 and
C-219 ETACS-ECU connector terminal No.66.
•
Check the input line for open circuit.
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair the wiring harness.
AC308722
Connector: C-219
Junction block (Rear view)
AH
68
74
63
66
72
73
67
6564
61
70
71
62
69
60
57
58
59
5655
52
54 53
51
Harness side
C-219(GR)
<LHD>
AC308776
Connector: C-219 <RHD>
Junction block (Rear view)
AE
68
74
63
66
72
73
67
6564
61
70
71
62
69
60
57
58
59
5655
52
54 53
51
Harness side
C-219(GR)
AC308722
Connector: C-219
Junction block (Rear view)
AH
68
74
63
66
72
73
67
6564
61
70
71
62
69
60
57
58
59
5655
52
54 53
51
Harness side
C-219(GR)
<LHD>
AC308776
Connector: C-219 <RHD>
Junction block (Rear view)
AE
68
74
63
66
72
73
67
6564
61
70
71
62
69
60
57
58
59
5655
52
54 53
51
Harness side
C-219(GR)
AC308724
Connector: C-310
AB
Harness side
10
5
6
7
9 8
3
4
2 1
<LHD>
AC308778
Connector: C-310
AB
Harness side
10
5
6
7
9 8
3
4
2 1
<RHD>
INPUT SIGNAL PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-324
Step 5. Retest the system.
Check that the windshield intermittent wiper volume
is sending a correct signal.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
−
How to
Cope with Intermittent Malfunction
NO :
Replace the ETACS-ECU.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст