Mitsubishi Outlander (2003+). Manual — part 308
FENDER
BODY
42-7
REMOVAL SERVICE POINT
<<A>> SIDE TURN SIGNAL LAMP REMOVAL
Use an appropriate tool such as special tool
Ornament remover MB990874 to pry out the tab from
the fender, and remove the side turn signal lamp.
INSTALLATION SERVICE POINT
>>A<< SIDE TURN SIGNAL LAMP INSTALLATION
Engage the hook with the fender panel, and install
the side turn signal lamp.
AC101384
Section A – A
: Front of vehicle
MB990784
Fender panel
Side turn signal lamp
A
A
Claw
AE
AC005719
Fender panel
Hook
Claw
Fender panel
: Front of vehicle
AE
FUEL FILLER LID
BODY
42-8
FUEL FILLER LID
REMOVAL AND INSTALLATION
M1421002500329
Pre-removal and Post-installation Operation
•
Rear Seat Removal and Installation (Refer to GROUP
52A, Rear Seat
).
•
Front Seat Assembly (Driver's Seat Side) Removal and
Installation (Refer to GROUP 52A, Front Seat
).
•
Front Seat Belt Anchor Bolt (Driver's Side) Removal and
Installation (Refer to GROUP 52A, Front Seat Belt
•
Front Scuff Plate (Driver's Side), Rear Scuff Plate
(Driver's Side), Centre Pillar Lower Trim (Driver's Side)
Removal and Installation (Refer to GROUP 52A, Trims
•
Floor Console Removal and Installation (Refer to GROUP
52A, Floor Console
AC107424
1
2
3
4
5
3
AC
5.0 ± 1.0 N·m
Fuel filler lid height and clearance
adjustment
Removal steps
1.
Fuel filler lid panel assembly
2.
Clip
3.
Fuel filler lid hook assembly
4.
Fuel filler lid lock release handle
•
Quarter lower trim (Refer to
GROUP 52A, Trims
•
Protector C (Refer to GROUP 36,
Parking Brake Cable
<LH
<RH drive
vehicles>).
5.
Fuel filler lid lock release cable
Removal steps (Continued)
WINDOW GLASS
BODY
42-9
WINDOW GLASS
ADHESIVE
M1422000500069
SPECIAL TOOL
M1422000600271
GENERAL
M1422000100436
The windshield, quarter window glass, tailgate
window glass and roof window glass are attached by
an urethane-base adhesive to the window frame.
This adhesive provides improved glass holding and
sealing, and also gives body openings a greater
structural strength.
ITEMS
HANDLING OF AUTO WINDOW SEALER
Keep the sealant in a cool place, not exposed to the
direct rays of the sun. Do not place any heavy article
on the sealant nor press it, otherwise it will become
deformed. Avoid storing the sealant for more than 6
months, because it will lose its sealing effect.
BODY PINCH-WELD FLANGE SERVICING
Before servicing the body pinch-weld flange, remove
old adhesive completely. If the flange requires
painting, bake it after painting is completed.
Item
Specified adhesive
Windshield
3M ATD Part No.8609 Super Fast Urethane Auto Glass
Sealant or equivalent
3M ATD Part No.8608 Super Fast Urethane Primer or
equivalent
Quarter window glass
Tailgate window glass
Roof window glass
Tool
Number
Name
Use
MB990480
Window glass holder Window glass removal and installation
MB990480
Name
Remark
Adhesive
3M ATD Part No.8609 Super Fast Urethane Auto Glass Sealant or
equivalent
Primer
3M ATD Part No.8608 Super Fast Urethane Primer or equivalent
Spacers
Available as service part
Dam
Available as service part
Anti-rust solvent (or Tectyl
506T.Valvoline Oil Company)
For rust prevention
Isopropyl alcohol
For grease removal from bonded surface
Steel piano wire
Dia.
×
length... 0.6mm
×
1m For cutting adhesive
Glass adhesive knife
For cutting adhesive
Adhesive gun
For pressing-out adhesive
WINDOW GLASS
BODY
42-10
WINDOW GLASS INSTALLATION
AC306636
Cleaning of adhesion surface
Cut off the residual adhesive until the
thickness is less than 2 mm. Clean the
adhesion surface with isopropyl alcohol,
and let dry for 3 minutes or more.
Cleaning of adhesion surface
Completely cut off all of the residual
adhesive. Clean the adhesive surface
with isopropyl alcohol, and let dry for
3 minutes or more.
Cleaning of adhesion surface
Clean off any dirt adhering to the adhesion
surface with isopropyl alcohol, and let dry
for 3 minutes or more.
Attaching of dual lock fastener
Attach the dual lock fastener to set the
positions for the glass to be installed.
Gluing of window dam and window spacer
Glue the window dam and window spacer to the glass, following the standard position
all the way around the inside edge of the glass.
Application of adhesive
Within 30 minutes after applying the primer, apply the adhesive evenly all the way around
the inside edge of the glass.
Installing the glass
After applying the adhesive, lightly press the glass evenly so that it adheres
completely.
Cleaning
After removing excess adhesive from the body or glass with a spatula, etc.
Clean off with isopropyl alcohol.
Checking for water leaks
Carry out a shower test to check that no water leaks through.
Replace the glass
Reusing the glass
Window glass installation procedure
Body side
Window glass side
Application of primer
Do not apply primer on residual adhesive as doing so may affect adhesion. apply enough primer on adhesion surface evenly taking
care not to apply it on the residual adhesive. after applying primer, let it dry for 3 minutes or more.
AD
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст