Mitsubishi Outlander (2003+). Manual — part 281

ABS SENSOR

ANTI-SKID BRAKING SYSTEM (ABS)

35B-67

ABS SENSOR

REMOVAL AND INSTALLATION

M1352020700038

REMOVAL SERVICE POINT

<<A>> FRONT ABS SENSOR/REAR ABS
SENSOR REMOVAL

CAUTION

Be careful when handling the projection at the tip
of the ABS sensor and the toothed edge of the
ABS rotor so as not to damage them by
contacting other parts.

Post-installation Operation

•

ABS Sensor Output Voltage Measurement (Refer to

P.35B-59

).

AC301105AB

<Front>

<Rear (2WD)>

1

2

4

3

3

4

<Rear (4WD)>

Front ABS sensor removal steps

<<A>>

1.

Front ABS sensor

2.

Front ABS rotor (Refer to GROUP
26, Driveshaft

P.26-20

).

Rear ABS sensor removal steps

<<A>>

3.

Rear ABS sensor

4.

Rear ABS rotor (Refer to GROUP
27A, Rear Hub Assembly

P.27A-5

for 2WD, or GROUP 27B,
Driveshaft

P.27B-13

for 4WD).

AC100242 AE

<Front, Rear (4WD)>

<Rear (2WD)>

ABS SENSOR

ANTI-SKID BRAKING SYSTEM (ABS)

35B-68

INSPECTION

M1352020800035

ABS SENSOR CHECK

1. Check whether any metallic foreign material has

adhered to the projection at the ABS sensor tip.
Remove any foreign material. Also check whether
the pole piece is damaged. Replace it with a new
one if it is damaged.
NOTE: The projection can become magnetized
due to the magnet inside the ABS sensor, causing
foreign material to easily adhere to it. The
projection may not be able to correctly sense the
wheel rotation speed if foreign matter is on it or if it
is damaged.

2. Measure the resistance between the ABS sensor

terminals.

Standard value: 1.24

−

1.64 k

Ω

3. If the internal resistance of the ABS sensor is not

within the standard value, replace it with a new
ABS sensor.

4. Remove all connections from the ABS sensor.

The circuit should be open between terminals (1)
and (2) and the body of the ABS sensor. If the
circuit is not open, replace with a new ABS
sensor.

5. Check the ABS sensor cable for breakage,

damage or disconnection. Replace with a new
one if a problem is found.
NOTE: When checking for cable damage, remove
the cable clamp part from the body and then
gently bend and pull the cable near the clamp.

TOOTHED ABS ROTOR CHECK

Check whether the ABS rotor teeth are broken or
deformed. Replace the BJ assembly of the
driveshaft, or the ABS rotor (2WD-rear side),
respectively, if the teeth are damaged or deformed.

AC201428AD

<Rear>

<Front>

ACX01120

AC000965

G-SENSOR

ANTI-SKID BRAKING SYSTEM (ABS)

35B-69

G-SENSOR

REMOVAL AND INSTALLATION

M1352010100251

CAUTION

Do not drop or apply a shock on the G-sensor.

INSPECTION

M1352018000065

G-SENSOR CHECK

1. Disconnect the G-sensor connector and connect

special tool Test Harness Set (MB991348),
between the disconnected connectors.

2. Turn the ignition switch to the "ON" position, and

then read the voltage between terminals number
2 and number 3.

Standard Value: 2.4

−

2.6 V

3. With special tool Test Harness Set (MB991348)

connected, rotate so that the arrow faces straight
down. Read output voltage between terminals
number 2 and number 3.

Standard Value: 1.0

−

4.0 V

4. If the voltage deviates from the standard value,

make sure that nothing is wrong with the power
supply wire and earth wire and then replace the
G-sensor.

Pre-removal and Post-installation Operation

•

Rear Floor Console Assembly Removal and Installation

(Refer to GROUP 52A, Floor Console Assembly

P.52A-14

).

AC200354

AC

G-sensor

AC103662AJ

MB991348

Connector: D-35
(Harness side)

Label

Label

NOTES