Mitsubishi Outlander (2003+). Manual — part 352
SERVICE PRECAUTIONS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-7
CAUTION
The SRS components and seat belt with
pre-tensioner should not be subjected to heat, so
remove the SRS-ECU, driver’s and front
passenger’s air bag modules, clock spring, side
air bag modules, and seat belt pre-tensioner
before drying or baking the vehicle after painting.
•
SRS-ECU, air bag modules, clock spring,
impact sensors: 93
°
C or more
•
Seat belt with pre-tensioner: 90
°
C or more
CAUTION
Whenever you finish servicing the SRS, always
erase the diagnosis code and check warning
lamp operation to make sure that the system
functions properly.
CAUTION
If checks are carried out by using the SRS-ECU
harness connector, observe the following
procedures: Insert the special tool (probe in the
harness set) MB991222 into connector from
harness side (rear side), and connect the tester
to this probe. If any tool than special tool is used,
damage to the harness and other components
will result. Never insert the probe directly to the
terminals from the front of the connector. The
terminals are plated to increase their
conductivity, so that if they are touched directly
by the probe, the plating may break, which will
cause drops in reliability.
AC300673AB
SRS-Harness connector
SRS-ECU harness connector
(rear side)
SPECIAL TOOLS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-8
SPECIAL TOOLS
M1524000700505
Tool
No.
Name
Application
MB990784
Ornament remover
Removal of cover.
MB991502
MUT-II sub assembly
•
Reading and erasing
diagnosis code
•
Reading trouble period
•
Reading erase times
MB991955
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991825
F: MB991826
MUT-III sub-assembly
A: Vehicle
Communication
Interface (V. C. I.)
B: MUT-III USB cable
C: MUT-III main
harness A (Vehicles
with CAN
communication system)
D: MUT-III main
harness B (Vehicles
without CAN
communication system)
E: MUT-III
measurement adapter
F: MUT-III trigger
harness
•
Reading and erasing
diagnosis code
•
Reading trouble period
•
Reading erase times
CAUTION
MUT-III main harness B
(MB991911) should be used.
MUT-III main harness A should
not be used for this vehicle.
MB991865
Dummy resistor
SRS air bag and seat belt with
pre-tensioner circuit check
MB991866
Resistor harness
SRS air bag circuit check
MB990784
B991502
MB991910
MB991826
MB991955
MB991911
MB991824
MB991827
MB991825
A
B
C
D
E
F
DO NOT USED
MB991865
MB991866
TEST EQUIPMENTS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-9
TEST EQUIPMENTS
M1524000800278
MB991884
Resistor harness (For
Pre-tensioner)
Seat belt with pre-tensioner
circuit check
MB991885
Pre-tensioner adapter
harness
•
Deployment of seat belt with
pre-tensioner inside the
vehicle
•
Deployment of seat belt with
pre-tensioner outside the
vehicle
MB991223
A: MB991219
B: MB991220
C: MB991221
D: MB991222
Harness set
A: Test harness
B: LED harness
C: LED harness
adapter
D: Probe
Checking the continuity and
measuring the voltage at the
SRS-ECU harness connector
MB686560
SRS air bag adapter
harness
•
Deployment of air bag module
(Front passenger's side) inside
the vehicle
•
Deployment of air bag module
(Front passenger's side)
outside the vehicle
Tool
No.
Name
Application
MB991884
MB991885
MB991223AW
A
B
C
D
MB686560
Tool
Name
Application
Digital multi-meter
Checking SRS electrical circuitry (Use
multi-meter for which the maximum test
current is 2 mA or less at minimum range
of resistance measurement
AC300683
TROUBLESHOOTING
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-10
TROUBLESHOOTING
DIAGNOSIS TROUBLESHOOTING FLOW
M1524003100353
Refer to GROUP 00
−
How to Use
Troubleshooting/Inspection Service Points
DIAGNOSIS FUNCTION
M1524003200402
DIAGNOSIS CODES CHECK
CAUTION
Turn off the ignition switch before connecting or
disconnecting the MUT-II/III.
Connect the MUT-II/III to the diagnosis connector
(16-pin) under the instrument under cover, then
check diagnosis codes (Refer to GROUP 00
−
How
to Use Troubleshooting/Inspection Service Points
ERASING DIAGNOSIS CODE
CAUTION
Turn off the ignition switch before connecting or
disconnecting the MUT-II/III.
Connect the MUT-II/III to the diagnosis connector
and erase the diagnosis code.
SRS WARNING LAMP CHECK
M1524004300297
1. Check that the SRS warning lamp comes on
when the ignition switch is turned ON.
2. Check that the SRS warning lamp illuminates for
about 7 seconds and then goes out.
3. If this is not the cause, check the diagnosis codes.
AC301667
SRS warning lamp
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст