Mitsubishi Outlander (2003+). Manual — part 144
IGNITION SYSTEM
ENGINE ELECTRICAL
16-41
REMOVAL AND INSTALLATION <4G69>
M1163004000501
CAMSHAFT POSITION SENSOR
REMOVAL AND INSTALLATION
M1163003400517
<4G63>
Pre-removal and Post-installation Operation
Resonator Removal and Installation (Refer to GROUP 15,
Air Cleaner
AC305115
10 ± 2 N·m
25 ± 5 N·m
1
2
3
AD
Removal steps
1.
Ignition coil connectors
2.
Ignition coils
3.
Spark plugs
Removal steps (Continued)
AC301556
N
1
2
3
8.8 ± 1.0 N·m
AB
Removal steps
1.
Camshaft position sensor
connector connection
2.
Camshaft position sensor
3.
O-ring
Removal steps (Continued)
IGNITION SYSTEM
ENGINE ELECTRICAL
16-42
<4G69>
CRANKSHAFT POSITION SENSOR
REMOVAL AND INSTALLATION <4G63>
M1163003500514
AC304319
AC302233
AC305127
N
1
2
3
11 ± 1 N·m
AC
Removal steps
1.
Camshaft position sensor
connector connection
2.
Camshaft position sensor
3.
O-ring
Removal steps (Continued)
AC301612
8.8 ± 1.0 N·m
7
8.8 ± 1.0 N·m
8
1
22 ± 4 N·m
4
2
3
49 ± 9 N·m
49 ± 9 N·m
5
22 ± 4 N·m
3.0 ± 0.5 N·m
6
IGNITION SYSTEM
ENGINE ELECTRICAL
16-43
REMOVAL SERVICE POINT
<<A>> POWER STEERING OIL PUMP ASSEMBLY
REMOVAL
Remove the power steering oil pump assembly from
the bracket with the hose attached.
NOTE: Place the removed power steering oil pump
assembly in a place where it will not be a hindrance
when removing and installing and secure it with a
cord or wire.
REMOVAL AND INSTALLATION <4G69>
M1163003500525
Removal steps
1.
Power steering pressure switch
connector
2.
A/C compressor connector
3.
A/C compressor connector clamp
<<A>>
4.
Power steering oil pump assembly
5.
Power steering oil pump bracket
6.
Rocker cover centre cover
7.
Crankshaft position sensor
8.
Crankshaft position sensor
connector bracket
Pre-removal and Post-installation Operation
Timing Belt Lower Cover Removal and Installation (Refer to
GROUP 11C, Timing Belt
AC305391
1
2
8.5 ± 0.5 N·m
AD
Removal steps
1.
Timing belt lower cover bracket
2.
Crankshaft position sensor
IGNITION SYSTEM
ENGINE ELECTRICAL
16-44
DETONATION SENSOR
REMOVAL AND INSTALLATION <4G63>
M1163002800631
CAUTION
Do not drop or hit the detonation sensor against other components. Internal damage may result, and
the detonation sensor will need to be replaced.
REMOVAL SERVICE POINT
<<A>> DETONATION SENSOR REMOVAL
Use special tool detonation sensor wrench
(MD998773) to remove the detonation sensor.
INSTALLATION SERVICE POINT
>>A<< DETONATION SENSOR INSTALLATION
Use special tool detonation sensor wrench
(MD998773) to tighten the detonation sensor to the
specified torque.
AC301657
2
1
23 ± 2 N·m
AB
<Intake side>
Removal steps
1.
Detonation sensor connector
connection
<<A>>
>>A<<
2.
Detonation sensor
AC100807
MD998773
Detonation
sensor
AC
AC100807
MD998773
Detonation
sensor
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст