Mitsubishi Outlander (2003+). Manual — part 403
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-7
IGNITION SWITCH
SPECIAL TOOLS
M1543000601845
Tool
Number
Name
Use
MB990784
Ornament remover
Removal of column cover
MB991502
MUT-II sub
assembly
•
Immobilizer system check
•
Encrypted code
registration
MB991958
A: MB991824
B: MB991827
C: MB991910
D: MB991911
E: MB991825
F: MB991826
MUT-III sub
assembly
A: Vehicle
communication
interface (V.C.I.)
B: MUT-III USB
cable
C: MUT-III main
harness A
(Vehicles with
CAN
communication
system)
D: MUT-III main
harness B
(Vehicles without
CAN
communication
system)
E:MUT-III
measurement
adapter harness
F: MUT-III trigger
harness
•
Immobilizer system check
•
Encrypted code
registration
CAUTION
MUT-III main harness B
(MB991911) should be used.
MUT-III main harness A and
C should not be used for
this vehicle.
MB990784
B991502
MB991910
MB991826
MB991955
MB991911
MB991824
MB991827
MB991825
A
B
C
D
E
F
DO NOT USED
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-8
INTRODUCTION
M1543009901360
IGNITION KEY REMINDER BUZZER
The ignition key reminder buzzer will sound under
the following condition, and warn the driver to
remove the ignition key.
•
The driver's door is opened when the ignition
switch is at "LOCK" (OFF) or "ACC" position
without removing the ignition key.
However, the lamp reminder buzzer will take
precedence over this function.
DOOR LOCK PREVENTION FUNCTION
If the key is left in the ignition switch while the driver’s
door opened or the assistant door opened, all door
are automatically unlock to prevent locking the
ignition key in the vehicle after door is locked.
IMMOBILIZER SYSTEM
The immobilizer system consists of the ignition key,
the immobilizer-ECU with key ring antenna, and the
engine-ECU <M/T> or engine-A/T-ECU <A/T>. The
ignition key has a built-in transponder. Only the
registered ignition key permits the engine to start,
therefore, the engine can never be started by means
of a forged key or by connecting the ignition wiring
directly. The system is significantly safe and reliable
against theft. In addition, the driver has only to turn
the ignition switch to the "ON" position to activate the
immobilizer system. If the requirements for starting
the engine are not satisfied, the engine will be
immobilized. If a registered ignition key is lost, all
your ignition keys need to be registered again using
MUT-II/III to ensure security (Refer to
). An
additional ignition key can be registered as follows
(only if no ignition keys are lost):
•
Using MUT-II/III (Refer to
OPERATION
1. When the ignition switch is turned to "ON"
position, the engine-ECU <M/T> or
engine-A/T-ECU <A/T> sends a requirement for
the encrypted code to the immobilizer-ECU (at
this time, the engine is remobilized).
2. When the immobilizer-ECU receives the
requirement from the engine-ECU <M/T> or
engine-A/T-ECU <A/T>, the immobilizer-ECU
supplies power to the transponder inside the
ignition key via the antenna. The energized
transponder sends the encrypted code back to the
immobilizer-ECU via the antenna.
3. The immobilizer-ECU judges the encrypted code
with its code logic in itself. If they are identical, the
immobilizer-ECU sends the encrypted code to the
engine-ECU <M/T> or engine-A/T-ECU <A/T>.
4. If the engine-ECU <M/T> or engine-A/T-ECU
<A/T> can not receive the encrypted code, the
engine will be immobilized.
MB991223
A: MB991219
B: MB991220
C: MB991221
D: MB991222
Harness set
A: Test harness
B: LED harness
C: LED harness
adapter
D: Probe
Making voltage and
resistance measurements
during troubleshooting
A: Connect pin contact
pressure inspection
B: Power circuit inspection
C: Power circuit inspection
D: Commercial tester
connection
Tool
Number
Name
Use
MB991223
A
B
C
D
AC
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-9
TROUBLESHOOTING
IGNITION KEY REMINDER BUZZER AND
DOOR LOCK PREVENTION FUNCTION
DIAGNOSIS
M1543000701109
The ignition key reminder buzzers are controlled by
the Smart Wiring System (SWS). For
troubleshooting, refer to respective Groups below.
•
Not using SWS monitor: GROUP 54B, SWS
Troubleshooting
•
Using SWS monitor: GROUP 54C, SWS
Troubleshooting
IMMOBILIZER SYSTEM DIAGNOSIS
DIAGNOSIS CODE CHART
M1543007100462
CAUTION
During diagnosis, a diagnosis code associated
with other system may be set when the ignition
switch is turned on with connector(s)
disconnected. On completion, confirm all
systems for diagnosis code code(s). If diagnosis
code code(s) are set, erase them all.
Use the following chart to develop proper diagnostic
strategy.
AC206892
Immobilizer-ECU
with an antenna
Power
(Wireress)
Encrypted code
(Wireless)
Ignition key
Steering lock
Control signal
MUT-II/III
Memory
Engine-ECU <M/T> or
engine-A/T-ECU <A/T>
AE
Encrypted
code
CPU
CPU
Transponder
Injector
Ignition
Diagnosis code No. Diagnosis item
Reference page
11
Transponder communication system or radio interference
of encrypted code
12
Encrypted codes are not the same or are not registered
IGNITION SWITCH
CHASSIS ELECTRICAL
54A-10
DIAGNOSTIC TROUBLE CODE
PROCEDURES
Code No.11: Transponder Communication System or Radio Interference of Encrypted Code
DIAGNOSIS CODE SET CONDITION
•
Diagnosis code No.11 may be output if other
ignition keys are in the vicinity of the vehicle as it
is being started.
•
The transponder’s encrypted code is not sent to
the immobilizer-ECU immediately after the
ignition switch is turned to "ON" position.
NOTE: Diagnosis code No.11 is always output
together with MPI system diagnosis code No.P1610.
TROUBLESHOOTING HINTS
•
Radio interference of the encrypted code
•
Malfunction of the transponder
•
Malfunction of the immobilizer-ECU.
DIAGNOSIS PROCEDURE
STEP 1. Check for presence of other key near the
key in the ignition.
Q: Is there any other key near the key in the ignition?
YES :
Move the other key well away from key
being used. Retest the system.
NO :
Go to Step 2.
STEP 2. Check that the engine start using the
spare ignition key which encrypted code has
been registered.
Q: Does the engine start using the spare ignition key
for which the encrypted code has been registered?
YES :
Replace the ignition key that does not work.
Then register the password (secret code)
and encrypted code
. Retest the
system.
NO :
Go to Step 3.
STEP 3. Check the MUT-II/III diagnosis code.
Q: Which diagnosis code is set, code No.11 or 12? the
encrypted code has been registered?
Code No.12 is set :
Refer to
.
Code No.11 is set :
Go to Step 4.
IGNITION
KEY RING
ANTENNA
IMMOBILIZER-ECU
HIGH FREQUENCY
CIRCUIT
IGNITION KEY
TRANSPONDER
AC300911
C-304-1
AB
Ignition Key Ring and Immobilizer-ECU Circuit
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст