Mitsubishi Outlander (2003+). Manual — part 488
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-241
DIAGNOSTIC PROCEDURE
Step 1. Check that the turn-signal lamps operate.
Check that the turn-signal lamps illuminate normally.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Refer to inspection procedure K-1 "The turn
signal lamps do not illuminate
Step 2. Check the power supply circuit.
When the ignition switch is at the LOCK (OFF)
position, check that the functions below work
normally.
•
Lamp reminder function
•
Central door locking system
•
Dome lamp (excluding interior lamp
automatic-shutdown function)
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Refer to inspection procedure A-2 "Check
the ETACS-ECU battery power supply
circuit
Step 3. Pulse check
Check the input signal from the hazard warning lamp
switch.
OK: The MUT-II/III sounds or the voltmeter
needle fluctuates.
Q: Is the check result normal?
The signal is received normally. :
Go to Step 4.
The hazard warning lamp switch signal is not
received. :
Refer to inspection procedure N-10
"The hazard warning lamp switch signal is
not received
Step 4. Retest the system.
Check that the hazard warning lamps illuminate.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
−
How to
Cope with Intermittent Malfunction
NO :
Replace the ETACS-ECU.
System switch
Check condition
Hazard warning lamp
switch
When the hazard
warning lamp switch is
turned from off to on
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-242
INSPECTION PROCEDURE K-3: Any of the turn-signal lamps does not illuminate.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
REAR
COMBINATION
LAMP (LH)
COMBINATION
METER
ETACS-ECU
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
HEADLAMP
ASSEMBLY
(FRONT TURN:
LH)
SIDE TURN
SIGNAL
LAMP
(LH)
(LH) (RH)
45
31
42
G
43
32
44
33
50
35
46
34
47
36
38
49
48
37
39
G
52
41
51
40
Turn-Signal Lamps Circuit <LHD>
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-243
ETACS-ECU
SIDE TURN
SIGNAL
LAMP
(LH)
REAR
COMBINATION
LAMP (LH)
COMBINATION
METER
HEADLAMP
ASSEMBLY
(FRONT TURN:
LH)
(RH)
(LH)
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Turn-Signal Lamps Circuit <RHD>
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-244
COMMENTS ON TROUBLE SYMPTOM
If any of the turn-signal lamp does not illuminate
normally, wiring harness connector(s) or the bulb
may be defective.
POSSIBLE CAUSES
•
Defective turn-signal lamp bulb
•
Damaged harness wires and connectors
ETACS-ECU
REAR
COMBINATION
LAMP (RH)
HEADLAMP
ASSEMBLY
(FRONT TURN:
RH)
SIDE TURN
SIGNAL
LAMP (RH)
Turn-Signal Lamps Circuit <LHD>
ETACS-ECU
REAR
COMBINATION
LAMP (RH)
HEADLAMP
ASSEMBLY
(FRONT TURN:
RH)
SIDE TURN
SIGNAL
LAMP (RH)
Turn-Signal Lamps Circuit <RHD>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст