Mitsubishi Outlander (2003+). Manual — part 397
SIDE IMPACT SENSOR
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-187
INSTALLATION SERVICE POINTS
>>A<< PRE-INSTALLATION INSPECTION
Even new side impact sensor requires inspection
before installation. (Refer to the previous item
"INSPECTION")
>>B<< SIDE IMPACT SENSOR INSTALLATION
WARNING
The side impact sensor, unless properly
installed, does not operate properly, thereby
resulting in serious injury or death of the
vehicle's occupants.
>>C<< POST-INSTALLATION INSPECTION
1. Connect the negative battery cable.
2. Turn the ignition key to "ON" position.
3. Does the SRS warning lamp illuminate for about 7
seconds, and then remain extinguished for at
least 5 seconds after turning OFF?
4. If no, refer to troubleshooting (Refer to
).
INSPECTION
M1524004700206
WARNING
If any problems, replace the sensor.
1. Check the side impact sensor and bracket for
dents, cracks or deformation.
2. Check the connector for damage, and terminal
for deformation.
3. Check that there is no bending or corrosion in the
centre pillar.
NOTE: For the checks other than the items above,
refer to Troubleshooting (Refer to
AC301667
SRS warning lamp
AB
SEAT BELTS WITH PRE-TENSIONER
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-188
SEAT BELTS WITH PRE-TENSIONER
REMOVAL AND INSTALLATION
M1524004100334
WARNING
•
Disconnect the negative battery terminal and wait for 60 seconds or more before starting
work. Furthermore, the disconnected battery terminal should be covered with tape to
insulate it.
•
Never attempt to disassemble or repair the seat belt pre-tensioner. If faulty, replace it.
•
Be extremely careful when handling the seat with pre-tensioner. Do not subject it to
shocks, drop it, bring it close to strong magnets or allow contact with water, grease or oil.
Always replace it with a new part if any dents, cracks or deformation is found.
•
Do not place anything on top of the seat belt pre-tensioner.
•
Do not expose the seat belt pre-tensioner to temperatures over 90
°
C.
•
After operating the seat belt pre-tensioner, replace the seat belt pre-tensioner with a new
part.
•
Gloves and protective goggles should be worn when handling a seat belt pre-tensioner
once it has been used.
•
If disposing of a seat belt with pre-tensioner which has not yet been operated, its seat belt
pre-tensioner should be operated first before disposal (Refer to
).
Pre-removal Operation
•
Turn the ignition key to the "LOCK" (OFF) position.
•
Disconnect the Negative Battery Terminal.
AC300144AB
1
2
3
4
5
6
44 ± 10 N·m
44 ± 10 N·m
SEAT BELTS WITH PRE-TENSIONER
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-189
NOTE: The figure shows the seat belt with
pre-tensioner (RH).
REMOVAL SERVICE POINTS
<<A>>PRE-TENSIONER CONNECTOR
DISCONNECTION
1. Use a flat-tipped screwdriver to pull out forward
and unlock the locking button of the harness-side
connector.
2. Disconnect the pretensioner connector.
INSTALLATION SERVICE POINTS
>>A<< PRE-INSTALLATION INSPECTION
WARNING
When discarding the seat belt with
pre-tensioner, operate the pre-tensioner as
specified in the service procedure (Refer to
1. Even new seat belt with pre-tensioner require
inspection before installation.
2. Connect the negative battery cable.
CAUTION
Turn the ignition switch to the "LOCK" (OFF)
position when connecting and disconnecting the
MUT-II/III.
3. Connect the MUT-II/III to the diagnosis connector
(16- pin).
4. Turn the ignition switch to the ON position.
5. Read a diagnosis code to refer to that the SRS is
operating properly except an open in the seat belt
with pre-tensioner circuit.
6. Turn the ignition switch to "LOCK" (OFF) position.
DANGER
Wait at least 60 seconds after the
disconnection of the battery cable before
any further job (Refer to
7. Disconnect the negative battery cable and
insulate with tape.
>>B<< PRE-TENSIONER CONNECTOR
CONNECTION
Connect the pretensioner connector then securely
lock the locking button of the harness-side
connector.
Removal steps
1. Sash guide cover
2. Seat belt shoulder anchor bolt
3. Seat belt lower anchor bolt
•
Centre pillar trim, lower (Refer to
GROUP 52A
−
Trims
<<A>>
4. Pre-tensioner connector connection
5. Bracket
6. Seat belt with pre-tensioner
Installation steps
>>A<<
•
Pre-installation inspection
6. Seat belt with pre-tensioner
5. Bracket
>>B<<
4. Pre-tensioner connector connection
•
Centre pillar trim, lower (Refer to
GROUP 52A
−
Trims
3. Seat belt lower anchor bolt
2. Seat belt shoulder anchor bolt
1. Sash guide cover
•
Negative battery cable connection
>>C<<
•
Post-installation inspection
Installation steps (Continued)
AC300147AB
Pre-tensioner
connector
Flat-tip screw
driver
Locking button
Harness side connector
SEAT BELTS WITH PRE-TENSIONER
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-190
>> C<< POST-INSTALLATION INSPECTION
1. Connect the negative battery cable.
2. Turn the ignition key to "ON" position.
3. Does the SRS warning lamp illuminate for about 7
seconds, and then remain extinguished for at
least 5 seconds after turning OFF?
4. If no, refer to troubleshooting (Refer to
INSPECTION
M1524004200223
WARNING
•
If any component damage is found during
the following inspection, replace the seat
belt with pre-tensioner with a new one.
Dispose of the old one according to the
specified procedure (Refer to
•
Never attempt to measure the circuit
resistance of the seat belt pre-tensioner
even if you are using the specified tester.
If the circuit resistance is measured with a
tester, accidental seat belt pre-tensioner
operation will result in serious personal
injury.
1. Check the pre-tensioner deployment section for
dents and deformation.
2. Check the harness and connector for damage and
the terminals for deformation.
AC301667
SRS warning lamp
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст