Mitsubishi Outlander (2003+). Manual — part 448
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-81
Step 21. Check the wiring harness from C-217
ETACS-ECU connector terminal Nos. 12 and 13 to
F-06 tailgate lock actuator connector terminal
Nos. 2 and 3.
NOTE:
Prior to the wiring harness inspection, check
intermediate connector F-05 and junction block
connector C-221, and repair if necessary.
•
Check the input and output lines for open circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
−
How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
AC308776
Connector: C-217
Junction block (Rear view)
Junction block side
AC
3
1
2
14
4
5
7 6
8
1110 9
1312
17
15
16
18
19
20
<RHD>
AC308809
Connectors: F-05, F-06
F-05
AB
F-05
F-06(B)
5
1
8
7
6
2
9 10
3 4
5
6
4
2
3
1
F-06
Harness side
AC308772
Connector: C-221 <RHD>
Harness side
AG
7
15
5
6
1413
2
9
12
4 3
10
11
1
8
Junction block (Front view)
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-82
INSPECTION PROCEDURE C-3: The central door locking system can not be operated by means of the
front passenger's door lock key cylinder.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
COMMENTS ON TROUBLE SYMPTOM
If the central door locking system does not work by
means of the front passenger's door lock key
cylinder, the front passenger's door lock key cylinder
or the ETACS-ECU may be defective.
POSSIBLE CAUSES
•
Malfunction of the front passenger's door lock key
cylinder
•
Malfunction of the ETACS-ECU
•
Damaged harness wires and connectors
ETACS-ECU
DOOR
UNLOCK
RELAY
DOOR
LOCK
RELAY
1
FUSIBLE
LINK
INPUT SIGNAL
FRONT
PASSENGER'S
DOOR LOCK KEY
CYLINDER SWITCH
DOOR LOCK ACTUATOR AND
TAILGATE LOCK ACTUATOR
· DOOR LOCK ACTUATOR
(FRONT: LH) <LHD>
· DOOR LOCK ACTUATOR
(FRONT: RH) <RHD>
Central Door Lock (Door Lock Key Cylinder Switch) Circuit
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-83
DIAGNOSTIC PROCEDURE
Step 1. Check the operation of the central door
locking system.
Check that the central door locking system works
normally by means of the driver's door lock key
cylinder and inside lock knob.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Refer to inspection procedure C-1 "Central
door locking system does not work at all
<L.H. drive vehicles>
or <R.H.
drive vehicles>
Step 2. Pulse check
Check the input signal from the front passenger’s
door lock key cylinder switch.
OK: The MUT-II/III sounds or the voltmeter
needle fluctuates.
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Refer to inspection procedure N-18 "The
front passenger's door lock key cylinder
switch signal is not received <L.H. drive
vehicles>
vehicles>
Step 3. Retest the system.
Check that the central door locking system works
normally by means of the front passenger's door lock
key cylinder.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
−
How to
Cope with Intermittent Malfunction
NO :
Replace the ETACS-ECU.
System switch
Check condition
Front passenger’s door
lock key cylinder switch
Turn the key to the lock
or unlock position
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-84
INSPECTION PROCEDURE C-4: The Ignition Key Reminder Function does not Work Normally.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
COMMENTS ON TROUBLE SYMPTOM
If the key reminder function does not work normally,
the input signal circuits below or the ETACS-ECU
may be defective.
•
Key reminder switch
•
Driver's door switch
•
Driver's door lock actuator
POSSIBLE CAUSES
•
Malfunction of the key reminder switch
•
Malfunction of the driver's door switch
•
Malfunction of the driver's door lock actuator
•
Malfunction of the ETACS-ECU
•
Damaged harness wires and connectors
DIAGNOSIS PROCEDURE
Step 1. Check the power supply circuit.
When the ignition switch is turned to the LOCK
(OFF) position, check if the hazard warning lamps
illuminate.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Refer to inspection procedure A-2 "Check
the ETACS-ECU battery power supply
circuit"
Step 2. Pulse check
Check the input signals below which are related to
the key reminder function.
OK: The MUT-II/III sounds or the voltmeter
needle fluctuates.
Q: Is the check result normal?
ETACS-ECU
DOOR
UNLOCK
RELAY
DOOR
LOCK
RELAY
1
FUSIBLE
LINK
DOOR LOCK ACTUATOR AND
TAILGATE LOCK ACTUATOR
· DOOR LOCK ACTUATOR
(FRONT: LH) <LHD>
· DOOR LOCK ACTUATOR
(FRONT: RH) <RHD>
INPUT SIGNAL
· KEY REMINDER
SWITCH
· DRIVER'S DOOR
SWITCH
· DRIVER'S DOOR
LOCK ACTUCTOR
SWITCH
Ignition Key Reminder Function
System switch
Check condition
Driver's door switch
When the driver's door is
opened
Key reminder switch
When the inserted
ignition key is pulled out
Driver's door lock
actuator switch
When the driver's key
cylinder or inside lock
knob is unlocked or
locked
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст