Mitsubishi Outlander (2003+). Manual — part 220
TRANSMISSION ASSEMBLY
AUTOMATIC TRANSMISSION (FF)
23A-175
>>B<< TRANSMISSION MOUNT STOPPER
INSTALLATION
Install the transmission mount stopper so that the
arrow mark points as shown in the illustration.
>>C<< TRANSMISSION STAY INSTALLATION
Install the transmission stay as below.
1. Tighten the engine-side bolts to the specified
torque.
Tightening torque: 22
±
4 N
⋅
m
2. Tighten the transmission-side bolts to the
specified torque.
Tightening torque: 44
±
10 N
⋅
m
>>D<< ADJUSTING NUT/TRANSMISSION
CONTROL CABLE INSTALLATION
1. Place the selector lever and manual control lever
in the N position.
2. Place the cable stud into the manual control lever
slot and install the nut loosely. Gently push the
transmission control cable into the manual control
lever slot until the cable is taut. Tighten the nut to
the specified torque.
Tightening torque: 12
±
2 N
⋅
m
AC005916
Transmission
mount bracket
Transmission
mount stopper
Engine side
AB
AC103395AO
Manual control lever
Adjusting nut
12 ± 2 N·m
TRANSFER ASSEMBLY
AUTOMATIC TRANSMISSION (FF)
23A-176
TRANSFER ASSEMBLY
REMOVAL AND INSTALLATION
M1231006000204
CAUTION
*
: Indicates parts which should be initially tightened, and then fully tightened after placing the vehicle
horizontally and loading the full weight of the engine on the vehicle body.
Pre-removal and Post-installation Operation
•
Under Cover Removal and Installation
•
A/T fluid Draining and Supplying (Refer to GROUP 23A,
On-vehicle Service
).
•
Transfer Oil Draining and Supplying (Refer to GROUP
23A, On-vehicle Service
).
•
Drive Shaft, Output Shaft Removal and Installation (Refer
to GROUP 26
).
•
Front Exhaust Pipe Removal and Installation (Refer to
GROUP 15, Exhaust Pipe and Main Muffler
•
Propeller Shaft Removal and Installation (Refer to
GROUP 25
AC309352
<LHD>
1
2
9
4
8
N
69 ± 10 N·m
69 ± 10 N·m
52 ± 7 N·m*
52 ± 7 N·m*
69 ± 10 N·m
69 ± 10 N·m
30 ± 3 N·m
9.0 ± 2.0 N·m
N
N
10
3
5
9.0 ± 2.0 N·m
30 ± 3 N·m
7
6
5
52 ± 7 N·m*
AB
Removal steps
1.
Water return tube assembly
2.
Gasket
3.
Water feed tube assembly
4.
Gasket
5.
Rear roll stopper connection bolt
6.
Centre member assembly
<<A>>
7.
Transfer assembly
8.
O-ring
9.
Water return hose
10. Water feed hose
Removal steps (Continued)
TRANSFER ASSEMBLY
AUTOMATIC TRANSMISSION (FF)
23A-177
REMOVAL SERVICE POINT
<<A>> TRANSFER ASSEMBLY REMOVAL
CAUTION
After pulling out the transfer assembly, upon
returning the transmission assembly to the
original position be careful not to damage the
bush parts of the roll stopper.
Use a tyre lever, etc. to slide the transmission
assembly to the front of the vehicle, create a
clearance between the transmission assembly and
crossmember, and then pull out the transfer
assembly from that clearance.
AC103630 AD
Cross member
Engine transmission
assembly
A/T FLUID COOLER
AUTOMATIC TRANSMISSION (FF)
23A-178
A/T FLUID COOLER
REMOVAL AND INSTALLATION
M1231028600099
Pre-removal and Post-installation Operation
•
Front Under Cover (LH) Removal and Installation (Refer
to GROUP 51, Under Cover
.)
•
Splash Shield Mounting Clips (LH) Removal and
Installation (Refer to GROUP 51, Front Bumper
.)
•
A/T Fluid Supplying (Refer to
.)
AC309337AB
1
12 ± 2 N·m
5
4
3
2
7 6
7
6
12 ± 2 N·m
Removal steps
1.
Cooler hose assembly
2.
A/T fluid cooler and bracket
3.
Bracket A
4.
Bracket B
5.
A/T fluid cooler
6.
Bush
7.
Collar
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст