Mitsubishi Grandis. Manual — part 966
TRANSMISSION
AUTOMATIC TRANSMISSION OVERHAUL
23B-20
11.Remove the valve body cover.
12.Remove the manual control shaft detent.
13.Disconnect the solenoid valve harness from the
valve body by undoing the fluid temperature
sensor and all the connectors.
CAUTION
Do not remove the bolts (four pieces) shown in
the illustration.
14.Remove the valve body mounting bolts (twenty
seven pieces).
CAUTION
Be careful not to lose the steel balls (2 pieces).
15.Remove the valve body, gasket and the steel
balls (2 pieces).
16.Remove the snap ring from the connector, then
push the connector into the transmission case to
remove the solenoid valve harness.
17.Remove the strainer and second brake retainer
oil seal.
AK300221
AK300222AC
Manual control shaft detent
AK300224AF
Fluid temperature sensor
AK300225AC
AK300226AC
Steel balls
AK300227AC
Snap ring
Connector
AK300228
Strainer
AC
Second brake
retainer oil seal
TRANSMISSION
AUTOMATIC TRANSMISSION OVERHAUL
23B-21
18.Remove the accumulator pistons and their
springs.
NOTE: Put tags to the removed accumulator
pistons and springs so that you will be able to
reinstall them in the correct positions.
19.Remove the manual control lever shaft roller.
20.Remove the manual control lever shaft and the
parking pawl rod.
21.Remove the converter housing mounting bolts,
then remove the converter housing.
22.Remove the differential bearing outer race and
spacer from the converter housing.
23.Remove the O-rings (2 pieces).
24.Remove the differential.
25.Remove the oil filter.
26.Remove the oil pump mounting bolts.
No.
Accumulator
1
For low-reverse brake
2
For underdrive clutch
3
For second brake
4
For overdrive clutch
AK300229AC
2
1
3
4
AK300230
Parking pawl rod
Manual control
lever shaft roller
Manual control
lever shaft
AC
AK201940
AK300232
AK201942
AK300234
AK300235
TRANSMISSION
AUTOMATIC TRANSMISSION OVERHAUL
23B-22
27.Install the special tools Oil pump remover as
shown in the drawing.
28.Screw the special tools evenly to remove the oil
pump.
29.Remove the oil pump gasket.
30.Remove the thrust washer #1.
31.Holding the input shaft, remove the underdrive
clutch.
32.Remove the thrust bearing #2.
33.Remove the underdrive clutch hub.
34.Pull out the parking pawl shaft, then remove the
spacer and spring.
35.Remove the parking roller support shafts (2
pieces), then remove the parking pawl and
parking roller support.
36.Remove the rear cover.
37.Remove the thrust race #8.
38.Remove the seal rings (4 pieces).
AK300236AC
MD998333
AK300237
AK300238
AK300239
AK300240
AK300241
AK300242
AK300463
TRANSMISSION
AUTOMATIC TRANSMISSION OVERHAUL
23B-23
39.Remove the input shaft rear bearing.
40.Remove the O-rings (three pieces).
41.Remove the reverse and overdrive clutch and the
thrust bearing #7.
42.Remove the overdrive clutch hub and thrust
bearing #6.
43.Remove the thrust bearing #5.
44.Remove the planetary reverse sun gear.
45.Remove the snap ring.
46.Remove the second brake piston and return
spring.
47.Remove the pressure plate, brake discs (three
pieces) and brake plates (two pieces).
AK300464
AK300465
AK300466
AK300467
AK300468
AK300469
AK300470
AK300471
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст