Mitsubishi Grandis. Manual — part 886
LOWER ARM
FRONT SUSPENSION
33-11
LOWER ARM BALL JOINT DUST COVER
CHECK
1. Check the dust cover for cracks or damage by
pushing it with your finger.
2. If the dust cover is cracked or damaged, replace
the lower arm assembly.
NOTE: Cracks or damage to the dust cover may
cause damage to the ball joint. When it is
damaged during service work, replace the dust
cover.
BALL JOINT DUST COVER
REPLACEMENT
M1332008200323
If the dust cover is damaged accidentally during
service work, replace the dust cover as follows:
1. Remove the dust cover.
2. Apply specified grease to the lip and the inside of
a new dust cover.
Specified grease: Multipurpose grease SAE
J310, NLGI No.2 or equivalent
Amount used for lip portion of dust cover: As
required
Amount used for the inside the dust cover:
10.0
± 0.5 g
3. Using special tool bearing installer (MD998911),
drive in the dust cover until it is seated on the
snap ring.
4. Check the dust cover for cracks or damage by
pushing it with your finger.
AC302426 AC
MD998911
Dust cover
Snap ring
STABILIZER BAR
FRONT SUSPENSION
33-12
STABILIZER BAR
REMOVAL AND INSTALLATION
M1332004000402
INSPECTION
M1332002000332
• Check the bushings for wear and deterioration.
• Check the stabilizer bar for deterioration or
damage.
• Check all bolts for condition and straightness.
STABILIZER LINK BALL JOINT TURNING
TORQUE CHECK
1. After shaking the ball joint stud several times,
install the nut to the stud and use special tool
preload socket (MB990326) to measure the
turning torque of the ball joint.
Standard value: 0
− 2.4 N⋅m
Post-installation Operation
² Front Wheel Alignment Check and Adjustment (Refer to
.)
AC301983AC
50 ± 10 N·m
1
2
3
4
5
6
89 ± 9 N·m
89 ± 9 N·m
Stabilizer link removal steps
1.
Stabilizer nut
2.
Stabilizer nut
3.
Stabilizer link
Stabilizer bushing removal
steps
1.
Stabilizer nut
•
Exhaust pipe hanger bracket
(Refer to GROUP 15, Exhaust
pipe and main muffler
.)
4.
Stabilizer bar bracket
5.
Stabilizer bushing
Stabilizer bar removal steps
1.
Stabilizer nut
•
Crossmember (Refer to
GROUP 32,
Crossmember
4.
Stabilizer bar bracket
5.
Stabilizer bushing
6.
Stabilizer bar
AC001129
MB990326
AB
STABILIZER BAR
FRONT SUSPENSION
33-13
2. When the measured value exceeds the standard
value, replace the stabilizer link.
3. Although the measured value is within the
standard value, if the ball joint is difficult to turn or
does not turn smoothly, replace the stabilizer link.
STABILIZER LINK BALL JOINT DUST
COVER CHECK
1. Check the dust cover for cracks or damage by
pushing it with your finger.
2. If the dust cover is cracked or damaged, replace
the stabilizer link.
NOTE: Cracks or damage of the dust cover may
cause damage to the ball joint.
34-1
GROUP 34
REAR SUSPENSION
CONTENTS
GENERAL INFORMATION . . . . . . . .
SERVICE SPECIFICATIONS. . . . . . .
ON-VEHICLE SERVICE. . . . . . . . . . .
REAR WHEEL ALIGNMENT CHECK AND
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . .
SHOCK ABSORBER ASSEMBLY . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION . . . . . . . . . . . . . . . . . . . . . . .
COIL SPRING . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
SEMI-TRAILING ARM ASSEMBLY (LOWER
ARM ASSEMBLY) . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
STABILIZER BAR. . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
REAR SUSPENSION CROSSMEMBER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст