Mitsubishi Grandis. Manual — part 813
RADIATOR
ENGINE COOLING
14-25
RADIATOR
REMOVAL AND INSTALLATION
M1141001500628
Pre-removal and Post-installation Operation
• Engine Coolant Draining and Supplying (Refer to
• Air Cleaner Assembly Removal and Installation (Refer to
GROUP 15
).
AC310381
1
2
3
4
4
8
9
13
12
7
15
10
17
14
14
5
6
6
20
23
16
22
21
19
18
11
21 ± 4 N·m
12 ± 2 N·m
N
N
N
N
AB
Radiator removal steps
1.
Drain plug
2.
Radiator cap
<<A>>
>>A<<
3.
Radiator upper hose
<<A>>
>>A<<
4.
Hose clips
<<A>>
>>A<<
5.
Radiator lower hose
<<A>>
>>A<<
6.
Hose clips
7.
A/T oil cooler hose connection
<A/T>
8.
Front end upper bar
9.
Radiator support upper insulator
10. Radiator condenser tank hose
11. Fan controller connector
<<B>>
12. A/C condenser connecting bolts
13. Radiator assembly
14. Radiator support lower insulator
15. A/T oil cooler hose <A/T>
16. Cooling fan motor and shroud
assembly
17. Radiator condenser tank assembly
18. Condenser fan motor connector
19. Cooling fan motor and fan
controller
20. Cooling fan
21. Cooling fan protector
22. Condenser fan motor
23. Condenser fan
Radiator condenser tank removal
steps
10. Radiator condenser tank hose
11. Fan controller connector
8.
Front end upper bar
Radiator removal steps
RADIATOR
ENGINE COOLING
14-26
REMOVAL SERVICE POINTS
<<A>> RADIATOR HOSE/HOSE CLIPS
DISCONNECTION
Break off the tip of hose clip claw and spread out the
hose clip, then disconnect the radiator hose.
NOTE: If there is a hose clip claw, the hose clip
cannot spread to capacity because the claw contacts
the hose clip.
<<B>> A/C CONDENSER CONNECTING
BOLTS REMOVAL
After removing the A/C condenser mounting bolts, tie
A/C condenser by string to secure. At this time, be
careful not to load the A/C pipe, etc.
INSTALLATION SERVICE POINT
>>A<< HOSE CLIPS/RADIATOR HOSE
CONNECTION
CAUTION
Never reuse the hose clip whose claw is broken
off to prevent the rusting.
1. Insert a new hose clip into the radiator hose.
2. Insert the radiator hose until the protrusion at both
radiator and engine side.
3. Remove the hose clip claw and shorten the hose
clip, then install the radiator hose.
9.
Radiator support upper insulator
17. Radiator condenser tank assembly
Radiator condenser tank removal
steps (Continued)
AC302615
Hose clip
Claw (Tip)
AE
32-1
GROUP 32
POWER PLANT
MOUNT
CONTENTS
GENERAL INFORMATION . . . . . . . .
SPECIAL TOOL . . . . . . . . . . . . . . . . .
ENGINE MOUNTING . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
TRANSMISSION MOUNTING . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
ENGINE ROLL STOPPER, CENTREMEMBER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
CROSSMEMBER . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
GENERAL INFORMATION
POWER PLANT MOUNT
32-2
GENERAL INFORMATION
M1321000100447
The engine mounting system employs the inertial
axis four-point suspension method, which is field
proven.
• The optimised locations of the front and rear roll
mounts well distribute their loads thereby
reducing engine idling vibrations.
• The fore-and-aft, liquid-filled engine mount of
cylinder type is adopted to reduce engine shake
for improved riding comfort.
CONSTRUCTION DIAGRAM
AC301843
AC302275
AC301844
Engine front
mounting bracket
Transmission mounting
body side bracket
Engine rear roll stopper bracket
Engine front roll stopper bracket
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст