Mitsubishi Grandis. Manual — part 508
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54D-130
STEP 34. Voltage measurement at C-09 joint
connector (CAN2).
CAUTION
A digital multimeter should be used. For details
refer to
CAUTION
The test wiring harness should be used. For
details refer to
(1) Disconnect the joint connector (CAN2) and the
A/C-ECU connector, and measure at the wiring
harness side.
(2) Connect the negative battery terminal, and turn
the ignition switch to the ON position.
(3) Voltage between C-09 joint connector (CAN2)
terminal No.8 and body earth
OK: Less than 1.0 V
(4) Disconnect the negative battery terminal.
CAUTION
Strictly observe the specified wiring harness
repair procedure. For details refer to
Q: Is the check result normal?
YES :
<less than 1.0 V> Follow diagnostic item 19
"Diagnose CAN bus lines thoroughly." Refer
to
.
NO :
<1.0 V or more> Repair the wiring harness
between the joint connector (CAN2) and the
A/C-ECU connector.
STEP 35. Connector check: C-221 ETACS-ECU
connector
CAUTION
The strand end of the twist wire should be within
10 cm from the connector. For details refer to
Q: Is the check result normal?
YES :
Go to Step 36 .
NO :
Repair the defective connector.
AC310628AY
Connector: C-09 <RHD>
C-09 (GR)
Harness side
AC310631AB
Connectors: C-106 <RHD>
Harness side
AC209365KR
Harness side: C-09
Test harness
AC310620
Connector: C-221
Junction block
(Rear view)
<RHD>
AC
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
Harness side
C-221(GR)
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54D-131
STEP 36. Voltage measurement at C-09 joint
connector (CAN2).
CAUTION
A digital multimeter should be used. For details
refer to
CAUTION
The test wiring harness should be used. For
details refer to
(1) Disconnect the joint connector (CAN2) and the
ETACS-ECU connector, and measure at the
wiring harness side.
(2) Connect the negative battery terminal, and turn
the ignition switch to the ON position.
(3) Voltage between C-09 joint connector (CAN2)
terminal No.5 and body earth
OK: Less than 1.0 V
(4) Disconnect the negative battery terminal.
CAUTION
Strictly observe the specified wiring harness
repair procedure. For details refer to
Q: Is the check result normal?
YES :
<less than 1.0 V> Follow diagnostic item 19
"Diagnose CAN bus lines thoroughly." Refer
to
.
NO :
<1.0 V or more> Repair the wiring harness
between the joint connector (CAN2) and the
ETACS-ECU connector.
STEP 37. Connector check: C-37 jumper
connector
CAUTION
The strand end of the twist wire should be within
10 cm from the connector. For details refer to
Check that the wiring harness of the jumper
connector is not damaged.
Q: Is the check result normal?
YES :
Go to Step 38 .
NO :
Repair the defective connector.
AC310628AY
Connector: C-09 <RHD>
C-09 (GR)
Harness side
AC310620
Connector: C-221
Junction block
(Rear view)
<RHD>
AC
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
Harness side
C-221(GR)
AC209365KJ
Harness side: C-09
Test harness
AC310628AZ
Connector: C-37 <RHD>
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54D-132
STEP 38. Voltage measurement at the C-09 joint
connector (CAN2).
CAUTION
A digital multimeter should be used. For details
refer to
CAUTION
The test wiring harness should be used. For
details refer to
(1) Disconnect the joint connector (CAN2) and the
jumper connector, and measure at the wiring
harness side.
(2) Connect the negative battery terminal, and turn
the ignition switch to the ON position.
(3) Voltage between C-09 joint connector (CAN2)
terminal No.9 and body earth
OK: Less than 1.0 V
(4) Disconnect the negative battery terminal.
Q: Is the check result normal?
YES :
<1.0 V or less> Go to Step 39.
NO :
<more than 1.0 V> Repair the wiring
harness between the joint connector
(CAN2) and the jumper connector.
STEP 39. Connector check: C-07 centre display
connector
CAUTION
The strand end of the twist wire should be within
10 cm from the connector. For details refer to
Q: Is the check result normal?
YES :
Go to Step 40 .
NO :
Repair the defective connector.
AC310628AY
Connector: C-09 <RHD>
C-09 (GR)
Harness side
AC310628AZ
Connector: C-37 <RHD>
AC209365KU
Harness side: C-09
Test harness
AC310631AY
Connector: C-07 <RHD>
Harness side
C-07 (B)
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54D-133
STEP 40. Voltage measurement at the C-37
jumper connector.
CAUTION
A digital multimeter should be used. For details
refer to
CAUTION
The test wiring harness should be used. For
details refer to
(1) Disconnect the centre display connector and the
jumper connector, and measure at the jumper
connector (at the centre display side).
(2) Connect the negative battery terminal, and turn
the ignition switch to the ON position.
(3) Voltage between C-37 jumper connector terminal
No.4 and body earth
OK: Less than 1.0 V
(4) Disconnect the negative battery terminal.
CAUTION
Strictly observe the specified wiring harness
repair procedure. For details refer to
Q: Is the check result normal?
YES :
<less than 1.0 V> Follow diagnostic item 19
"Diagnose CAN bus lines thoroughly." Refer
to
.
NO :
<1.0 V or more> Repair the wiring harness
between the jumper connector and the
centre display connector.
STEP 41. Connector check: C-119 SRS-ECU
connector
CAUTION
The strand end of the twist wire should be within
10 cm from the connector. For details refer to
Q: Is the check result normal?
YES :
Go to Step 42 .
NO :
Repair the defective connector.
AC310631AY
Connector: C-07 <RHD>
Harness side
C-07 (B)
AC310628AZ
Connector: C-37 <RHD>
AC312551 AC
Harness side: C-37
Test
harness
AC310631AZ
Connector: C-119 <RHD>
Harness side
C-119 (Y)
48
37
26
42
31
45
34
47
36
46
35
44
33
43
32
25 24
39
28
41
30
40
29
38
27
23
21
22
A
B
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст