Mitsubishi Grandis. Manual — part 238
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-414
COMMENTS ON TROUBLE SYMPTOM
If the rear personal lamps do not illuminate or
extinguish normally, wiring harness connector(s) or
the bulb may be defective.
POSSIBLE CAUSES
• Malfunction of the interior lamp switches
• Malfunction of the room lamp bulbs
• Malfunction of the rear personal lamp bulbs
• Damaged harness wires and connectors
ETACS-ECU
J/B SIDE
ROOM LAMP
INTERIOR
LAMP
SWITCH
REAR
PERSONAL
LAMP
FOR
SECOND
SEAT: LH
REAR
PERSONAL
LAMP
FOR
SECOND
SEAT: RH
REAR
PERSONAL
LAMP
FOR
THIRD
SEAT: LH
REAR PERSONAL LAMP
(FOR THIRD SEAT: RH)
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Room Lamp and Rear Personal Lamp Circuit
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-415
DIAGNOSTIC PROCEDURE
Step 1. SWS monitor data list
<Selected item> ETACS ECU
• Driver's door is open
OK: Normal condition is displayed.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Refer to inspection procedure Q-5 "The
driver's door switch signal is not received
<LH drive vehicles>
vehicles>
Step 2. ETACS switch data by using the SWS
monitor
Check the ETACS-ECU signal related to the rear
personal lamp illumination.
• Ignition switch: OFF (key inserted)
• Passenger’s door: Close → Open
• Tailgate: Close → Open
• Rear door (RH): Close → Open
• Rear door (LH): Close → Open
• Driver’s door: Unlock → Lock
• Room lamp on switch: ON
• Room lamp off switch: ON
OK: Normal conditions displayed for all the
items.
Q: Is the check result normal?
Item No.
Item name
Normal
condition
Item 32
DR DOOR SW
ON
Item No.
Item name
Normal
condition
Item 03
KEY REMINSW
OFF
Item No.
Item name
Normal
condition
Item 05
PASS DOOR SW
from OFF
to ON
Item No.
Item name
Normal
condition
Item 07
TRK LID LA SW
from OFF
to ON
Item No.
Item name
Normal
condition
Item 41
R.DOOR(RH) SW
from OFF
to ON
Item No.
Item name
Normal
condition
Item 42
R.DOOR(LH) SW
from OFF
to ON
Item No.
Item name
Normal
condition
Item 21
DR DOR LOK SW
from OFF
to ON
Item 22
DR DOR ULOK SW
from ON
to OFF
Item No.
Item name
Normal
condition
Item 31
RM LMP ON SW
ON
Item No.
Item name
Normal
condition
Item 32
RM LMP OFF SW
ON
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-416
Normal conditions are displayed for all the items. :
Go to Step 3.
Normal condition is not displayed for item No.03 :
Refer to inspection procedure Q-11 "The
key reminder switch signal is not received
Normal condition is not displayed for item No.05,
07, 41or 42 :
Refer to inspection procedure Q-14
"All the door switch signals are not received
Normal condition is not displayed for item No.21
and 32 :
Refer to inspection procedure Q-15 "The
driver's door lock actuator switch signal is
not received <LH drive vehicles>
Normal condition is not displayed for item No.31 or
32 :
Refer to inspection procedure Q-22 "The
interior lamp "all on" or "all off" switch signal
is not sent to the ETACS-ECU
Step 3. Retest the system.
Check which lamp does not illuminate when the lamp
switches are operated.
Q: Which lamp does not illuminate?
No lamps illuminate :
Go to Step 4.
One of the second seat lamps (RH or LH) or the
third seat lamps (RH or LH) does not illuminate. :
Go to Step 8.
Step 4. Check the rear personal lamp switches.
Check which position (ON or DOOR) of the rear
personal lamp switch does not activate the relevant
lamp.
Q: Which switch position does not activate the lamp?
The lamp illuminates at neither the ON nor DOOR
position. :
Go to Step 5.
The lamp does not illuminate at the DOOR position.
:
Go to Step 7.
The lamp does not illuminate at the ON position. :
Replace the rear personal lamp.
Step 5. Connector check: C-219 ETACS-ECU
connector, E-09 rear personal lamp connector
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Repair the defective connector.
AC310626
Connector: C-219
Junction block (Rear view)
<LHD>
AB
Junction block side
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
AC310651
AC310651
AG
Connector: E-09 <LHD>
Harness side
AC310655
AC310655
AH
Connector: E-09 <RHD>
Harness side
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-417
Step 6. Check the wiring harness from C-219
ETACS-ECU connector terminal No.6 to E-09 rear
personal lamp connector terminal No.2.
NOTE:
Prior to the wiring harness inspection, check
intermediate connector E-11 and junction block
connector C-211, and repair if necessary.
• Check the earth wires for open circuit.
Q: Is the check result normal?
YES :
Replace the rear personal lamp.
NO :
Repair the wiring harness.
AC310626
Connector: C-219
Junction block (Rear view)
<LHD>
AB
Junction block side
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
AC310651
AC310651
AG
Connector: E-09 <LHD>
Harness side
AC310655
AC310655
AH
Connector: E-09 <RHD>
Harness side
AC310623
AC310623
Connector: C-211
AQ
<LHD>
Junction block (Front view)
Harness side
3
1
2
AC310618
AC310618
Connector: C-211 <RHD>
AS
Harness side
Junction block (Front view)
3
1
2
AC310651
AC310651
AH
Connector: E-11 <LHD>
AC310655
AC310655
AI
Connector: E-11 <RHD>
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст