Mitsubishi Grandis. Manual — part 295
TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION
55-65
Step 5. Check the wiring harness between C-10
outside/inside air selection damper control motor
connector terminal No.1 and the ignition switch
(IG2).
NOTE:
Prior to the wiring harness inspection, check joint
connector C-31 and junction block connectors C-205
and C-202, and repair if necessary.
• Check the motor power supply line for open
circuit.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00, How to
Cope with Intermittent Malfunction
NO :
Repair the wiring harness.
Step 6. Check the outside/inside air selection
damper control motor
Refer to
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Replace the outside/inside air selection
damper control motor.
Step 7. Connector check: C-105 A/C-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Repair the connector.
AC310615
AH
Harness side
Connector: C-10 <LHD>
AC310613
AP
Connector: C-31 <LHD>
AC310624
Connectors: C-202, C-205 <LHD>
AF
Junction block (Front view)
C-205
C-202
C-205
Harness side
C-202
Harness side
AC310613
AC
Connector: C-105 <LHD>
Harness side
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION
55-66
Step 8. Check the wiring harness between C-105
A/C-ECU connector (terminals 37 and 38) and
C-10 outside/inside air selection damper control
motor connector (terminals 2 and 3).
• Check the motor activating lines for open or short
circuit.
Q: Is the check result normal?
YES :
Replace the automatic air conditioner
control panel (A/C-ECU).
NO :
Repair the wiring harness.
AC310615
AH
Harness side
Connector: C-10 <LHD>
AC310613
AC
Connector: C-105 <LHD>
Harness side
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION
55-67
INSPECTION PROCEDURE 6: The inside/outside air changeover is impossible. <RHD>
COMMENTS ON TROUBLE SYMPTOM
When inside air cannot be changed to outside air
vice versa even if its changeover switch is on, the
outside/inside air selection damper control motor
system may be defective.
POSSIBLE CAUSES
• Malfunction of the outside/inside air selection
damper control motor
• Damaged the wiring harness or connectors
• Malfunction of the automatic air conditioner
control panel (A/C-ECU)
DIAGNOSIS
STEP 1. Check the operation of the heater control
panel
Check that the A/C switch, rear window defogger
switch and air volume control dial can operate.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
INSPECTION PROCEDURE 27: Refer to
A/C-ECU power supply system
<RHD>
Step 2. MUT-III actuator test
Carry out the actuator test.
• Item 30: In/out changeover dumper: Recirc
• Item 31: In/out changeover dumper: Fresh
Q: Does the blower motor work normally?
YES :
Replace the automatic air conditioner
control panel (A/C-ECU)
NO :
Go to Step 3.
A/C-ECU
IGNITION
SWITCH (IG2)
OUTSIDE/INSIDE AIR
SELECTION DAMPER
CONTROL MOTOR
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Outside/Inside Air Selection Damper Control Motor Circuit
TROUBLESHOOTING
HEATER, AIR CONDITIONER AND VENTILATION
55-68
Step 3. Connector check: C-10 outside/inside air
selection damper control motor connector
Q: Is the check result normal?
YES :
Go to Step 4.
NO :
Repair the connector.
Step 4. Voltage measurement at C-10
outside/inside air selection damper control motor
connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Turn the ignition switch to the ON position.
(3) Measure the voltage between terminal 1 and
body earth.
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Go to Step 5.
AC310628AI
Harness side
Connector: C-10 <RHD>
AC310628AI
Harness side
Connector: C-10 <RHD>
AC310507AR
Connector C-10
(Harness side)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст