Mitsubishi Grandis. Manual — part 54
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-213
Inspection Procedure G-2: The windshield wipers does not work when the wiper switch is at "INT",
"WASHER" or "MIST" position. However, the wipers work at low speed when the switch is at "LO" and
"HI" position.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
COMMENTS ON TROUBLE SYMPTOM
The system may be at fail-safe mode as the SWS
communication line is defective. If the front-ECU
does not receive the ignition switch (ACC) signal due
to an open circuit in the SWS communication lines or
other reasons when the ignition switch is at the ACC
position, the system will enter the fail-safe mode.
POSSIBLE CAUSES
• Malfunction of the column switch
• Malfunction of the front-ECU
• Damaged harness wires and connectors
DIAGNOSTIC PROCEDURE
Step 1. MUT-III diagnosis code
When the ignition switch is turned to the LOCK
(OFF) position, check that the ETACS-ECU does not
set the diagnosis code.
Q: Is the diagnosis code set?
YES :
Refer to diagnosis code chart
.
NO :
Go to Step 2.
Step 2. Pulse check.
Check the input signals below which are related to
the windshield wiper.
OK: The MUT-III sounds or the voltmeter
needle fluctuates.
Q: Are the check result normal?
Windshield Wiper Motor Drive Circuit
Wire colour code
B : Black LG : Light green G : Green L : Blue
W : White Y : Yellow SB : Sky blue BR : Brown
O : Orange GR : Gray R : Red P : Pink V : Violet
CIRCUIT
BREAKER
FRONT-ECU
INPUT SIGNAL
· WINDSHIELD WIPER HI SPEED SWITCH
· WINDSHIELD WIPER INTERMIT SWITCH
· WINDSHIELD WIPER LO SPEED SWITCH
· WINDSHIELD WIPER MIST SWITCH
WIPER SPEED
SWITCHING
RELAY
WINDSHIELD
WIPER MOTOR
System switch
Check condition
Ignition switch (ACC)
When turned from the
LOCK (OFF) position to
the ACC position.
Windshield mist wiper
switch
When the switch is
turned from off to on.
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-214
All the signals are received normally :
Go to Step
The ignition switch (ACC) signal is not received. :
Refer to inspection procedure Q-1 "The
ignition switch (ACC) signal is not received
Windshield mist wiper switch signal is not
received. :
Refer to inspection procedure Q-7 "The
column switch (windshield wiper washer
and rear wiper washer switch) signal is not
received
."
Step 3. Retest the system.
The windshield wiper should now work normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Replace the front-ECU.
Inspection Procedure G-3: The windshield wipers do not stop at the specified park position
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
COMMENTS ON TROUBLE SYMPTOM
The windshield wiper motor or the front-ECU may be
defective.
POSSIBLE CAUSES
• Malfunction of the windshield wiper motor
• Malfunction of the front-ECU
• Damaged harness wires and connectors
Windshield Wiper Automatic Stop Relay Circuit
IGNITION
SWITCH (ACC)
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
FRONT-ECU
WINDSHIELD
WIPER MOTOR
WIPER
AUTOMATIC
STOP RELAY
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-215
DIAGNOSTIC PROCEDURE
Step 1. Connector check: A-01 windshield wiper
motor connector.
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the connector.
Step 2. Check the windshield wiper motor
assembly.
Refer to GROUP 51
− Windshield wiper
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Replace the windshield wiper motor
assembly.
Step 3. Voltage measurement at the A-01
windshield wiper motor connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Ignition switch: ACC
(3) Check the voltage between the A-01 windshield
wiper motor connector terminal No.3 and body
earth.
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Go to Step 4.
AC310401
Connector: A-01 <LHD>
Harness side
AD
A-01 (GR)
AC310396
Connector: A-01 <RHD>
Harness side
AD
A-01 (GR)
AC310401
Connector: A-01 <LHD>
Harness side
AD
A-01 (GR)
AC310396
Connector: A-01 <RHD>
Harness side
AD
A-01 (GR)
AC310507
Connector A-01
(Harness side)
BY
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-216
Step 4. Check the wiring harness between A-01
windshield wiper motor connector terminal No.3
and ignition switch (ACC).
NOTE:
AC310401
Connector: A-01 <LHD>
Harness side
AD
A-01 (GR)
AC310396
Connector: A-01 <RHD>
Harness side
AD
A-01 (GR)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст