Mitsubishi Grandis. Manual — part 393
SPECIAL TOOLS
FRONT AXLE
26-4
SPECIAL TOOLS
M1261000600513
Tool
Number
Name
Use
MB990767
End yoke holder
Fixing of the hub
MB991618
Hub bolt remover Removal of the hub bolt
MB991897
Ball joint remover Knuckle and tie rod end ball joint
disconnection
NOTE: Steering linkage puller
(MB990635 or MB991113)is also used
to disconnect knuckle and tie rod end
ball joint.
MB990241
A: MB990242
B: MB990244
Axle shaft puller
A: Puller shaft
B: Puller bar
Removal of the drive shaft
MB991354
Puller body
A: MB991017
B: MB990998
C: MB991000
A, B: Front hub
remover and
installer
C: Spacer
• Provisional holding of the wheel
bearing
• Measurement of wheel bearing
starting torque
• Measurement of wheel bearing axial
play
NOTE: MB991000, which belongs to
MB990998, should be used as a
spacer.
B990767
MB991618
AC106827
MB990241AB
A
B
MB991354
AC100320AB
A
B
C
SPECIAL TOOLS
FRONT AXLE
26-5
MB990685
Torque wrench
Measurement of wheel bearing starting
torque
MB990326 Preload
socket
MB990810
Side bearing
puller
Removal of the centre bearing bracket
MB991172
Inner shaft
installer base
Press-fitting of the inner shaft
MB991248 or
MD998801
Inner shaft
remover
Removal of the inner shaft
MB991460
Plug
Prevention of entry of foreign objects
MB990925
Bearing and oil
seal installer set
• Removal and installation of the
centre bearing
• Press-fitting of the dust seal outer,
inner
MB990890
Rear suspension
bushing base
Press-fitting of the dust seal outer, inner
Tool
Number
Name
Use
MB990326
MB990810
MB991248
MB990925
MB990890
ON-VEHICLE SERVICE
FRONT AXLE
26-6
ON-VEHICLE SERVICE
WHEEL BEARING AXIAL PLAY CHECK
M1261000900257
1. Remove the caliper assembly and suspend it with
a wire.
2. Remove the brake disc from the front hub.
3. Attach a dial gauge as shown in the illustration,
and then measure the axial play while moving the
hub in the axial direction.
Limit: 0.05 mm
4. If axial play exceeds the limit, disassemble the
front hub assembly and check the parts.
5. Install the brake disc, caliper assembly and
tighten the caliper assembly mounting bolts to the
specified torque 100
± 10 N⋅m.
HUB BOLT REPLACEMENT
M1261001000321
1. Remove the caliper assembly and suspend it with
wire so that it does not fall.
2. Remove the brake disc.
3. Use the following special tools to remove the hub
bolts.
• End yoke holder (MB990767)
• Hub bolt remover (MB991618)
Tool
Type
Tool number
O D mm
A
MB990926
39.0
MB990927
45.0
MB990928
49.5
MB990929
51.0
MB990930
54.0
MB990931
57.0
MB990932
61.0
MB990933
63.5
MB990934
67.5
MB990935
71.5
MB990936
75.5
MB990937
79.0
B
MB990938
−
C
MB990939
−
ACX02372
A
B
C
Brass bar
Bar (snap-in type)
Tool box
MB990925
AC
Installer adapter
AC102438
AC102439 AC
MB990767
MB991618
ON-VEHICLE SERVICE
FRONT AXLE
26-7
4. Install the plain washer to the new hub bolt, and
install the bolt with a nut.
5. Install the brake disc, caliper assembly and
tighten the caliper assembly mounting bolts to the
specified torque 100
± 10 N⋅m.
AC102440
MB990767
Plain
washer
AC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст