Mitsubishi Grandis. Manual — part 332
REAR A/C SWITCH
HEATER, AIR CONDITIONER AND VENTILATION
55-213
REAR A/C SWITCH
REMOVAL AND INSTALLATION
M1554017200022
INSPECTION
M1552014301414
REAR HEATER CONTROLLER
CONTINUITY CHECK
AC303126
2
1
1
2
AB
<Vehicles with sunroof>
<Vehicles without sunroof>
Removal steps
1.
Rear heater controller (Refer to
GROUP 52A, Headlining
•
Headlining (Refer to GROUP 52A,
Headlining
2.
Rear heater controller bracket
AC303225
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17 18 19 20
REAR HEATER UNIT
HEATER, AIR CONDITIONER AND VENTILATION
55-214
REAR AIR VOLUME ADJUSTING SWITCH
REAR TEMPERATURE CONTROL KNOB
<VEHICLES WITH DUAL AUTOMATIC
A/C>
Check that the resistance value between connector
terminals 14 and 15 changes gradually within the
standard value when moving the knob.
Standard value: Approximately 3k
Ω or less
REAR HEATER UNIT
REMOVAL AND INSTALLATION
M1554015300023
Switch status
Checking
terminal
Normal
conditions
OFF
4
− 9
2
Ω or less
AUTO
<vehicles with
dual automatic
A/C>
5
− 9
2
Ω or less
1
6
− 9
2
Ω or less
2
7
− 9
2
Ω or less
3
8
− 9
2
Ω or less
Pre-removal and Post-installation Operation
• Engine coolant Draining and Refilling (Refer to GROUP
14, On vehicles service
• Refrigerant draining and Refilling (Refer to Charging
• Third seat assembly removal and installation (Refer to
GROUP 52A, Third Seat Assembly
.)
• Quarter trim lower and quarter trim upper removal and
installation (Refer to GROUP 52A, Interior Trim
AC303098
2
3
6
5
1
AB
4
4
N
13.7 ± 1.0 N·m
32 ± 2 N·m
3
A/C compressor oil:
SUN PAG 56
-Pipe coupling
REAR HEATER UNIT
HEATER, AIR CONDITIONER AND VENTILATION
55-215
REMOVAL SERVICE POINTS
<<A>> REAR A/C PIPE REMOVAL
CAUTION
Use the plug which is not breathable because
A/C compressor oil or receiver have high
hygroscopicity.
Plug the pipe nipple to prevent the entry of dust and
dirt.
DISASSEMBLY AND REASSEMBLY
<VEHICLES WITH REAR HEATER, REAR
COOLER OR DUAL AUTOMATIC A/C>
M1554017600019
Removal steps
1.
Rear pillar duct
2.
Rear floor duct A
<<A>>
3.
Rear A/C pipe connection
4.
O ring
5.
Heater hose connection
6.
Rear heater unit
AC302508
11
2
1
12
13
14
11
10
8
7
9
5
3
4
6
AB
Removal steps
1.
Rear blower motor <Vehicles with
rear heater, rear cooler or dual
automatic A/C>
2.
Rear power transistor <Vehicles
with rear heater, rear cooler or dual
automatic A/C>
3.
Harness <vehicles with dual
automatic A/C>
4.
Rear air mix damper control motor
<Vehicles with dual automatic A/C>
5.
Rear heater pipe bracket <Vehicles
with rear heater or dual automatic
A/C>
6.
Rear heater core <Vehicles with
rear heater or dual automatic A/C>
7.
Rear air mix lever <Vehicles with
dual automatic A/C>
8.
Rear mode selection damper lever
A <Vehicles with dual automatic
A/C>
Removal steps (Continued)
REAR HEATER UNIT
HEATER, AIR CONDITIONER AND VENTILATION
55-216
INSPECTION
M1552014301425
CHECK THE REAR AIR MIX DAMPER
MOTOR AND POTENTIOMETER
<VEHICLES WITH DUAL AUTOMATIC
A/C>
CAUTION
Stop energizing when the lever is set to the
operation stopping position.
MOTOR CHECK
Potentiometer check
When the resistance value between connector
terminals 3 and 5 is measured while checking the
motor, check that the resistance value changes
gradually within the standard value.
Standard value: 1.20 (MAX COOL)
− 4.80
(MAX HOT) k
Ω
9.
Rear mode selection damper lever
B <Vehicles with dual automatic
A/C>
10. Rear mode selection damper lever
C <Vehicles with dual automatic
A/C>
11. Rear heater case <Vehicles with
rear heater, rear cooler or dual
automatic A/C>
12. Evaporator <vehicles with rear
cooler or dual automatic A/C>
13. Rear mode selection damper
<Vehicles with dual automatic A/C>
14. Rear mode selection damper
<Vehicles with dual automatic A/C>
Removal steps (Continued)
AC302969
MAX
COOL
MAX
HOT
1 2 3 4 5
AB
Battery
connection (+)
terminal
Battery
connection (-)
terminal
Lever
operation
2
1
Rotate to the
MAX HOT side.
1
2
Rotate to the
MAX COOL
side.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст