Mitsubishi Grandis. Manual — part 787
ENGINE-ECU AND ENGINE-A/T-ECU
MULTIPORT FUEL INJECTION (MPI)
13A-399
ENGINE-ECU AND ENGINE-A/T-ECU
REMOVAL AND INSTALLATION
M1131022500053
<L.H. drive vehicles>
CAUTION
Always register the ignition key(s) when the engine-ECU <M/T> or the engine-A/T-ECU <A/T> is
replaced (Refer to GROUP 54A, On-vehicle Service - Immobilizer ID Code Registration
INSTALLATION SERVICE POINT
>>A<< LNITIALIZATION
When the Engine-ECU <M/T> or Engine-A/T-ECU
<A/T> is replaced, initialize the electronic-controlled
throttle valve system according to the procedure
below beforehand.
Turn the ignition switch to the ON position, and
back to the "LOCK" (OFF) position. Then hold it in
this position for approximately 10 seconds or
more.
Pre-removal Operation
• Front Scuff Plate (RH), Cowl Side Trim (RH) Removal
(Refer to GROUP 52A Trims
).
• Console Side Cover (RH) Removal (Refer to GROUP
52A, Floor Console assembly
).
Post-installation Operation
• Console Side Cover (RH) Installation (Refer to GROUP
52A, Floor Console assembly
).
• Front Scuff Plate (RH), Cowl Side Trim (RH) Installation
(Refer to GROUP 52A Trims
AC310595
1
5.0 ± 1.0 N·m
2
3
4
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
AB
REMOVAL STEPS
>>A<<
•
Initialization (Installation only)
•
Turn up the floor mat. <Front
passenger's side>
1.
Wiring harness clamp connection
2.
Bracket
3.
Engine-ECU connector <M/T> or
Engine-A/T-ECU connector <A/T>
4.
Engine-ECU <M/T> or
Engine-A/T-ECU <A/T>
ENGINE-ECU AND ENGINE-A/T-ECU
MULTIPORT FUEL INJECTION (MPI)
13A-400
<R.H. drive vehicles>
CAUTION
Always register the ignition key(s) when the engine-ECU <M/T> or the engine-A/T-ECU <A/T> is
replaced (Refer to GROUP 54A, On-vehicle Service - Immobilizer ID Code Registration
INSTALLATION SERVICE POINT
>>A<< LNITIALIZATION
When the Engine-ECU <M/T> or Engine-A/T-ECU
<A/T> is replaced, initialize the electronic-controlled
throttle valve system according to the procedure
below beforehand.
Turn the ignition switch to the ON position, and
back to the "LOCK" (OFF) position. Then hold it in
this position for approximately 10 seconds or
more.
Pre-removal Operation
• Front Scuff Plate (LH), Cowl Side Trim (LH) Removal
(Refer to GROUP 52A Trims
).
• Console Side Cover (LH) Removal (Refer to GROUP
52A, Floor Console assembly
).
Post-installation Operation
• Console Side Cover (LH) Installation (Refer to GROUP
52A, Floor Console assembly
).
• Front Scuff Plate (LH), Cowl Side Trim (LH) Installation
(Refer to GROUP 52A Trims
AC301810
1
5.0 ± 1.0 N·m
2
3
4
5
5.0 ± 1.0 N·m
5.0 ± 1.0 N·m
AC301810AC
REMOVAL STEPS
>>A<<
•
Initialization (Installation only)
•
Turn up the floor mat. <Front
passenger's side>
1.
Wiring harness clamp connection
2.
Wiring harness clamp connection
3.
Bracket
4.
Engine-ECU connector <M/T> or
Engine-A/T-ECU connector <A/T>
5.
Engine-ECU <M/T> or
Engine-A/T-ECU <A/T>
15-1
GROUP 15
INTAKE AND
EXHAUST
CONTENTS
GENERAL INFORMATION . . . . . . . .
SERVICE SPECIFICATION . . . . . . . .
SEALANT. . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOL . . . . . . . . . . . . . . . . .
AIR CLEANER . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INLET MANIFOLD . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
EXHAUST MANIFOLD . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
INSPECTION. . . . . . . . . . . . . . . . . . . . . . . .
EXHAUST PIPE AND MAIN MUFFLER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
GENERAL INFORMATION
INTAKE AND EXHAUST
15-2
GENERAL INFORMATION
M1151000100509
The exhaust pipe is divided into three parts.
SERVICE SPECIFICATION
M1151000300525
SEALANT
M1151000500228
SPECIAL TOOL
M1151000600474
Item
Standard value
Limit
Manifold distortion of the installation surface mm
0.15 or less
0.20
Item
Specified sealant
Thermostat case assembly
MITSUBISHI GENUINE Part No.MD970389 or equivalent
Thermostat case assembly bolt
3M Stud Locking 4170 or equivalent
Tool
Number
Name
Use
MB991953
Oxygen sensor wrench
Removal and installation of
oxygen sensor
B991953
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст