Mitsubishi Grandis. Manual — part 903
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-27
NOTE: Do not connect special tool ABS Check
Harness (MB991974) to the ABS-ECU.
(2) Turn the ignition switch to the "ON" position.
(3) Measure the voltage between the relevant signal
and earth terminals in the wheel speed sensor
circuit and body earth.
OK: Less than 1V
• Code No.C1201 is set: Between signal
terminal 5 and body earth, and between earth
terminal 6 and body earth
• Code No.C1206 is set: Between signal
terminal 8 and body earth, and between earth
terminal 9 and body earth
• Code No.C1211 is set: Between signal
terminal 11 and body earth, and between
earth terminal 12 and body earth
• Code No.C1216 is set: Between signal
terminal 2 and body earth, and between earth
terminal 3 and body earth
Q: Is the check result normal?
YES :
Go to Step 9.
NO (When the voltage between terminal 5 or 6
−
and body earth measures more than 1 V) :
Go to
Step 10.
NO (When the voltage between terminal 8 or 9
−
and body earth measures more than 1 V) :
Go to
Step 11.
NO (When the voltage between terminal 11 or 12
−
and body earth measures more than 1 V) :
Go to
Step 12.
NO (When the voltage between terminal 2 or 3
−
and body earth measures more than 1 V) :
Go to
Step 13.
STEP 9. Resistance measurement at ABS-ECU
connector A-03.
(1) Disconnect the connector A-03, and connect
special tool ABS Check Harness (MB991974) to
the wiring harness-side connector.
NOTE: Do not connect special tool ABS Check
Harness (MB991974) to the ABS-ECU.
(2) Measure the resistance between the relevant
signal and earth terminals in the wheel speed
AC312620AS
Oil reservoir
Connector: A-03
ABS-ECU
MB991974
Check connector
A-03 Harness connector
A-03
Hydraulic unit
(with built-in ABS-ECU)
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-28
sensor circuit and body earth.
OK: No continuity
• Code No.C1201 is set: Between signal
terminal 5 and body earth, and between earth
terminal 6 and body earth
• Code No.C1206 is set: Between signal
terminal 8 and body earth, and between earth
terminal 9 and body earth
• Code No.C1211 is set: Between signal
terminal 11 and body earth, and between
earth terminal 12 and body earth
• Code No.C1216 is set: Between signal
terminal 2 and body earth, and between earth
terminal 3 and body earth
Q: Is the check result normal?
YES (Continuity exists between terminal 5 or
terminal 6 and body earth) :
Go to Step 10.
YES (Continuity exists between terminal 8 or
terminal 9 and body earth) :
Go to Step 11.
YES (Continuity exists between terminal 11 or
terminal 12 and body earth) :
Go to Step 12.
YES (Continuity exists between terminal 2 or
terminal 3 and body earth) :
Go to Step 13.
NO :
Go to Step 14.
STEP 10. Check ABS-ECU connector A-03 and
wheel speed sensor <front: RH> connector A-02
for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Is the check result normal?
AC312621
Oil reservoir
Connector: A-03
AC
A-03
Hydraulic unit
(with built-in ABS-ECU)
A-03 Harness connector
(harness side)
AC312616AB
Connector: A-02
A-02 (GR)
A-02 Harness
connector
(harness side)
AC312618AB
Connector: A-02 <R.H.drive vehicles>
A-02 (GR)
A-02 Harness
connector
(harness side)
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-29
YES :
Open or short circuit may be present in the
front right wheel speed sensor circuit.
Repair the wiring harness between
ABS-ECU connector A-03 (terminals 5 and
6) and front right wheel speed sensor A-02
(terminals 1 and 2). Then go to Step 15.
NO :
Repair or replace the damaged
component(s). Then go to Step 15.
STEP 11. Check ABS-ECU connector A-03 and
wheel speed sensor <front: LH> connector A-05
for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Q: Is the check result normal?
AC312621
Oil reservoir
Connector: A-03
AC
A-03
Hydraulic unit
(with built-in ABS-ECU)
A-03 Harness connector
(harness side)
AC312617AB
Connector: A-05 <L.H.drive vehicles>
A-05 (GR)
A-05 Harness
connector
(harness side)
AC312619AB
Connector: A-05 <R.H.drive vehicles>
A-05 (GR)
A-05 Harness
connector
(harness side)
TROUBLESHOOTING
ANTI-SKID BRAKING SYSTEM (ABS)
35B-30
YES :
Open or short circuit may be present in the
front right wheel speed sensor circuit.
Repair the wiring harness between
ABS-ECU connector A-03 (terminals 8 and
9) and front left wheel speed sensor A-05
(terminals 2 and 1). Then go to Step 15.
NO :
Repair or replace the damaged
component(s). Then go to Step 15.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст