Mitsubishi Grandis. Manual — part 803
AUTO-CRUISE CONTROL
ENGINE AND EMISSION CONTROL
17-53
ON-VEHICLE SERVICE
AUTO-CRUISE CONTROL SWITCH
CHECK
M1172001200098
AUTO-CRUISE CONTROL MAIN SWITCH
CHECK
1. Turn the ignition switch to ON position.
2. Check that the auto-cruise control indicator lamp
within the combination meter illuminates when the
MAIN switch is switched ON.
113
Throttle position
sensor (sub)
• Remove the intake air hose at
the throttle body
• Disconnect the throttle position
sensor, and then connect
terminal numbers No. 3, No. 4,
No. 5 and No. 6 with the use of
the special tool (MB991658).
• Ignition switch: "ON"
Fully close the
throttle valve
with your finger
2.2
− 2.8 V
Fully open the
throttle valve
with your finger
4.0 V or more
114
Accelerator pedal
position sensor
(main)
Ignition
switch: "ON"
Release the accelerator pedal
0.9
− 1.2 V
Depress the accelerator pedal.
4.0 V or more
115
Throttle position
sensor (main)
• Remove the intake air hose at
the throttle body
• Disconnect the throttle position
sensor, and then connect
terminal numbers No. 3, No. 4,
No. 5 and No. 6 with the use of
the special tool (MB991658).
• Ignition switch: "ON"
Fully close the
throttle valve
with your finger
0.3
− 0.7 V
Fully open the
throttle valve
with your finger
4.0 V or more
132
Engine-ECU <M/T>
or Engine-A/T-ECU
<A/T> power supply
voltage applied to
throttle valve control
servo
Ignition switch: "ON"
System voltage
Terminal
No.
Check item
Check conditions
Normal
condition
AC311410
AC311198
MAIN switch: ON
AB
Auto-cruise control
indicator lamp
AUTO-CRUISE CONTROL
ENGINE AND EMISSION CONTROL
17-54
AUTO-CRUISE CONTROL SETTING
1. Switch ON the MAIN switch.
2. Drive at the desired speed within the range of
approximately 40
− 200 km/h.
3. Push the auto-cruise control switch in the
direction of arrow.
4. Check to be sure that when the switch is released
the speed is the desired constant speed.
NOTE: If the vehicles speed decreases to
approximately 15 km/h below the set speed
because of climbing a hill for example, the
auto-cruise control will be cancelled.
SPEED-INCREASE SETTING
1. Set to the desired speed.
2. Push the auto-cruise control switch in the
direction of arrow.
3. Check to be sure that acceleration continues
while the switch is hold, and that when it is
released the constant speed at the time when it
was released becomes the driving speed.
NOTE: Acceleration can be continued even if the
vehicle speed has passed the high-speed limit
(approximately 200 km/h). But the speed when
the auto-cruise control switch is released will be
recorded as the high-speed limit.
SPEED-REDUCTION SETTING
1. Set to the desired speed.
2. Push the auto-cruise control switch in the
direction of arrow.
3. Check to be sure that deceleration continues
while the switch is pressed, and that when it is
released the constant speed at the time when it
was released becomes the driving speed.
NOTE: When the vehicle speed reaches the low
limit (approximately 40 km/h) during deceleration,
the auto-cruise control will be cancelled.
RETURN TO THE SET SPEED BEFORE
CANCELLATION AND AUTO-CRUISE
CONTROL CANCELLATION
1. Set the auto-cruise speed control.
2. When any of the following operations are
performed while at constant speed during
auto-cruise control, check if normal driving is
resumed and deceleration occurs.
(1) The auto-cruise control switch is pulled in the
direction of arrow.
(2) The brake pedal is depressed.
(3) The selector lever is moved to the "N" range.
AC310956
AC310954
AC310955
AC310956
AC310957
AUTO-CRUISE CONTROL
ENGINE AND EMISSION CONTROL
17-55
3. When the auto-cruise control switch is pushed in
the direction of arrow at a vehicle speed of 40
km/h or higher, check if the vehicle speed returns
to the speed before auto-cruise control driving
was cancelled, and constant speed driving
occurs.
4. When the MAIN switch is turned to OFF while
driving at constant speed, check if normal driving
is resumed and deceleration occurs.
AUTO-CRUISE CONTROL SYSTEM
COMPONENT CHECK
M1172001700424
AUTO-CRUISE CONTROL SWITCH
CHECK
1. Remove the auto-cruise control switch. (Refer to
2. Measure the resistance between the terminals
when each of the SET, RESUME, CANCEL and
MAIN switches is pressed. If the values measured
at the time correspond to those in the table below,
then there is no problem.
STOP LAMP SWITCH
1. Disconnect the connector.
2. Check for continuity between the terminals of the
switch.
CLUTCH SWITCH <M/T>
Refer to GROUP 21A, On-vehicle Service
− Clutch
Pedal Switch Check and Adjustment
INHIBITOR SWITCH ("N" POSITION)
<A/T>
Refer to GROUP 23A, On-vehicle Service
− A/T
Control Component Check
AC310956
1 2 3
AC203822AB
OFF
OFF
OFF
OFF
ON
ON
ON
ON
CAN
MAIN
RES
SET
2
3
Switch position
Specified condition
MAIN switch: OFF
Open circuit
MAIN switch: ON
Less than 2
Ω
CANCEL switch: ON
Approximately 100
Ω
RESUME switch: ON
Approximately 887
Ω
SET switch: ON
Approximately 300
Ω
Measurement
conditions
Terminal
connector of
tester
Specified
condition
When brake
pedal is
depressed. (for
stop lamp
circuit)
1
− 2
Less than 2
Ω
3
− 4
Open circuit
When brake
pedal is not
depressed. (for
auto-cruise
control circuit)
1
− 2
Open circuit
3
− 4
Less than 2
Ω
ACX01180AB
AUTO-CRUISE CONTROL
ENGINE AND EMISSION CONTROL
17-56
THROTTLE POSITION SENSOR
Refer to GROUP 13A, On-vehicle Service
− Throttle
Valve Control Servo Check
AUTO-CRUISE CONTROL
REMOVAL AND INSTALLATION
M1172001400360
WARNING
•
Before removal of the air bag module, refer to GROUP 52B, Service Precautions (
and Driver’s, Front Passenger’s Air Bag Module(s) and Clock Spring (
•
When removing and installing the steering wheel and air bag module assembly, do not let
it bump against the air bag module.
AC311572
1
1.7 ± 0.2 N·m
2
6
5
3
AB
7
8
4
Auto-cruise control switch removal
steps
•
Air bag module (Refer to GROUP
52B, Driver’s, Front Passenger’s Air
Bag Module(s) and Clock Spring
)
1. Auto-cruise control switch
Control unit removal
2. Engine-ECU <M/T> or
Engine-A/T-ECU <A/T> (Refer to
GROUP 13A, Engine-ECU and
Engine-A/T-ECU
Sensor removal steps
3. Inhibitor switch <A/T>
4. Accelerator pedal (Refer to
5. Vehicle speed sensor <M/T>
6. Throttle body assembly (Refer to
GROUP 13A, Throttle body assembly
7. Stop lamp switch (Refer to GROUP
35A, Brake pedal
8. Clutch switch <M/T> (Refer to
GROUP 21A, Clutch pedal
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст