Mitsubishi Grandis. Manual — part 1041
POST-COLLISION DIAGNOSIS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-216
3. Check the sensor harnesses for binding, the
connectors for damage, and the terminals for
deformation.
NOTE: The figures show front impact sensors (LH).
The side impact sensors (RH) are symmetrical with
the side impact sensors (LH).
SRS-ECU
1. Check the SRS-ECU case and brackets for dents,
cracks or deformation.
2. Check the connector for damage, and the
terminals for deformation.
3. Check the SRS-ECU and bracket for installation
condition.
AIR BAG MODULES
1. Check the pad cover for dents, cracks or
deformation.
2. Check the connector for damage, terminals
deformities, and the harness for binding.
3. Check the air bag inflator case for dents, cracks or
deformities.
4. Check the air bag modules for proper installation.
FRONT SEAT BACK ASSEMBLY (SIDE
AIR BAG MODULE)
1. Check the side air bag module deployment
section in the seat for dents and deformation.
2. Check the connectors for damage, the terminals
for deformation, and the harness for binds.
AC300929
AC311438
AC312488AB
SRS-ECU
Shift lever assembly
AC312188AB
Inflator case
Connector
<Driver's side>
<Passenger's (front) side>
Inflator case
Connector
AC303516
AD
Side-airbag module
deployment section
POST-COLLISION DIAGNOSIS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-217
CLOCK SPRING
1. Check the clock spring connectors and protective
tube for damage, and the terminals for
deformation.
2. Visually check the case for damage.
SIDE IMPACT SENSOR
1. Check the centre pillar for deformation or rust.
2. Check the side impact sensors for dents, cracks,
deformation and rust.
3. Check the connector for damage and the
terminals for deformation.
NOTE: The figures show side impact sensors
(RH). The side impact sensors (LH) are
symmetrical with the side impact sensors (RH).
SEAT BELT WITH PRE-TENSIONER
1. Check the seat belt for damage or deformation.
2. Check the seat belt with pre-tensioner for cracks
or deformation.
3. Check that the unit is installed correctly to the
vehicle body.
CURTAIN AIR BAG MODULES
1. Check that the curtain air bag deployment part of
the headlining is normal.
2. Check the inflator surface for cracks, dents or
deformations.
3. Check the air bag for breakage.
4. Check the connector for damage, the terminal for
deformation and the harness for binding.
SEAT SLIDE SENSOR
1. Check that there is no connector damage, bent
terminals or harness crimping.
2. Check the installation of the seat slide sensor.
AC306766AD
Case
Protective tubes
AC302574
AC311614
AC312491
Centre pillar
Second
seat belt
Side impact
sensor (rear)
Side impact
sensor (front)
<Front>
<Rear>
AB
AC302258AC
Inflator
Curtain air bag module
deployment section
AC311621
AC312492
AC311625
Seat slide
adjuster
Seat slide
sensor
Front seat
(Driver's side)
AB
INDIVIDUAL COMPONENT SERVICE
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-218
PASSENGER’S AIR BAG CUT OFF
SWITCH
1. Check the passenger’s air bag cut off switch for
dents or deformation.
2. Check the installation of the passenger’s air bag
cut off switch.
STEERING WHEEL, STEERING COLUMN
AND SHAFT ASSEMBLY
1. Check the wiring harness (built into the steering
wheel) and the connectors for damage, and the
terminals for deformation.
2. Install the air bag module to check fit or alignment
with the steering wheel.
3. Check the steering wheel for noise, binding or
difficult operation and excessive free play.
4. Check the steering column shaft shock absorbing
mechanism (Refer to GROUP 37, On-Vehicle
Service
HARNESS CONNECTOR (INSTRUMENT
PANEL WIRING HARNESS AND FLOOR
WIRING HARNESS, ROOF WIRING
HARNESS)
Check harnesses for binding, connectors for damage
and terminals for deformation (Refer to
INDIVIDUAL COMPONENT SERVICE
M1524002900442
WARNING
•
If heat damage may occur during paint work, remove the SRS-ECU, the air bag modules,
the clock spring, front seats, side impact sensors and the seat belt with pre-tensioner.
•
SRS-ECU, air bag modules, clock spring and side impact sensors: 93
°
C or more
•
Seat belt with pre-tensioner: 90
°
C or more
•
If the SRS components are removed for the purpose of check, sheet metal repair, painting,
etc., they should be stored in a clean, dry place until they are reinstalled.
If the SRS components are to be removed or replaced as a result of maintenance, troubleshooting etc., follow
the service procedures that follow. (SRS-ECU; refer to
, Driver’s and passenger’s (front) air bag
modules and clock spring; refer to
, Side and curtain air bag modules; refer to
impact sensor ; refer to
, Side impact sensors; refer to
, Seat belt with pre-tensioner ;
, Seat slide sensor ; refer to
, Passenger’s air bag cut off switch ; refer to
).
WARNING/CAUTION LABELS
M1524003000163
Caution labels on the SRS are attached in the vehicle as shown. Follow label instructions when servicing the
SRS. If the label(s) are dirty or damaged, replace with new one(s).
AC312598AB
Passenger's air bag
cut off switch
Glove box
WARNING/CAUTION LABELS
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-219
AC312005
AC302070
AC302072
AC302189
AC302123
AC302187
AC311401
AC311369
AC311626
AC311623
AC311408
AC311881
AC
SRS-ECU
Steering wheel
Driver's air bag module
Clock spring
Passenger's (front)
air bag module
Sun visor*
Glove box
Steering joint cover
Seat belt with pre-tensioner
(driver's and passenger's seat)
Side air bag module
Front impact sensor
Hood
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст