Mitsubishi Grandis. Manual — part 549
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54D-294
STEP 40. Resistance measurement at the C-09
joint connector (CAN2).
CAUTION
A digital multimeter should be used. For details
refer to
CAUTION
The test wiring harness should be used. For
details refer to
(1) Disconnect the joint connector (CAN2) and the
jumper connector, and measure at the wiring
harness side.
CAUTION
When measuring the resistance, disconnect the
negative battery terminal. For details refer to
(2) Ensure that the negative battery terminal is
disconnected.
(3) Resistance between C-09 joint connector (CAN2)
terminal No.9 and body earth
OK: 1 k
Ω or more
Q: Is the check result normal?
YES :
<1 k
Ω or more> Go to Step 41.
NO :
<less than 1 k
Ω> Repair the wiring harness
between the joint connector (CAN2) and the
jumper connector.
STEP 41. Connector check: C-07 centre display
connector
CAUTION
The strand end of the twist wire should be within
10 cm from the connector. For details refer to
Q: Is the check result normal?
YES :
Go to Step 42 .
NO :
Repair the defective connector.
AC302572AD
Connector: A-07
Harness side
AC310628AY
Connector: C-09 <RHD>
C-09 (GR)
Harness side
AC209364MI
Harness side: C-09
Test harness
AC310631AY
Connector: C-07 <RHD>
Harness side
C-07 (B)
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54D-295
STEP 42. Resistance measurement at the C-37
jumper connector.
CAUTION
A digital multimeter should be used. For details
refer to
CAUTION
The test wiring harness should be used. For
details refer to
(1) Disconnect the centre display connector and the
jumper connector, and measure at the jumper
connector (at the centre display side).
CAUTION
When measuring the resistance, disconnect the
negative battery terminal. For details refer to
(2) Ensure that the negative battery terminal is
disconnected.
(3) Resistance between C-37 jumper connector
terminal No.4 and body earth
OK: 1 k
Ω or more
CAUTION
Strictly observe the specified wiring harness
repair procedure. For details refer to
Q: Is the check result normal?
YES :
<1 k
Ω or more> Follow diagnostic item 20,
Diagnose CAN bus lines thoroughly. Refer
to
.
NO :
<less than 1
Ω> Repair the wiring harness
between the jumper connector and the
centre display connector.
STEP 43. Connector check: C-119 SRS-ECU
connector
CAUTION
The strand end of the twist wire should be within
10 cm from the connector. For details refer to
Q: Is the check result normal?
YES :
Go to Step 44.
NO :
Repair the defective connector.
AC310631AY
Connector: C-07 <RHD>
Harness side
C-07 (B)
AC310628AZ
Connector: C-37 <RHD>
A
AC312552 AC
Harness side: C-37
Test
harness
AC310631AZ
Connector: C-119 <RHD>
Harness side
C-119 (Y)
48
37
26
42
31
45
34
47
36
46
35
44
33
43
32
25 24
39
28
41
30
40
29
38
27
23
21
22
A
B
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54D-296
STEP 44. Resistance measurement at C-09 joint
connector (CAN2).
CAUTION
A digital multimeter should be used. For details
refer to
CAUTION
The test wiring harness should be used. For
details refer to
(1) Disconnect the joint connector (CAN2) and the
SRS-ECU connector, and measure at the wiring
harness side.
CAUTION
When measuring the resistance, disconnect the
negative battery terminal. For details refer to
(2) Ensure that the negative battery terminal is
disconnected.
(3) Resistance between C-09 joint connector (CAN2)
terminal No.4 and body earth
OK: 1 k
Ω or more
CAUTION
Strictly observe the specified wiring harness
repair procedure. For details refer to
Q: Is the check result normal?
YES :
<1 k
Ω or more> Follow diagnostic item 20,
Diagnose CAN bus lines thoroughly. Refer
to
.
NO :
<less than 1 k
Ω> Repair the wiring harness
between the joint connector (CAN2) and the
SRS-ECU connector.
STEP 45. Connector check: C-306 steering wheel
angle sensor connector
CAUTION
The strand end of the twist wire should be within
10 cm from the connector. For details refer to
Q: Is the check result normal?
YES :
Go to Step 46.
NO :
Repair the defective connector.
AC310628AY
Connector: C-09 <RHD>
C-09 (GR)
Harness side
AC310631AZ
Connector: C-119 <RHD>
Harness side
C-119 (Y)
48
37
26
42
31
45
34
47
36
46
35
44
33
43
32
25 24
39
28
41
30
40
29
38
27
23
21
22
A
B
AC209364LY
Harness side: C-09
Test
harness
AC310183
AF
Connector: C-306 <RHD>
Harness side
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54D-297
STEP 46. Resistance measurement at C-09 joint
connector (CAN2).
CAUTION
A digital multimeter should be used. For details
refer to
CAUTION
The test wiring harness should be used. For
details refer to
(1) Disconnect the joint connector (CAN2) and the
steering wheel angle sensor connector, and
measure at the wiring harness side.
CAUTION
When measuring the resistance, disconnect the
negative battery terminal. For details refer to
(2) Ensure that the negative battery terminal is
disconnected.
(3) Resistance between C-09 joint connector (CAN2)
terminal No.3 and body earth
OK: 1 k
Ω or more
CAUTION
Strictly observe the specified wiring harness
repair procedure. For details refer to
Q: Is the check result normal?
YES :
<1 k
Ω or more> Follow diagnostic item 20,
Diagnose CAN bus lines thoroughly. Refer
to
.
NO :
<less than 1 k
Ω> Repair the wiring harness
between the joint connector (CAN2) and the
steering angle sensor connector.
STEP 47. Resistance measurement at C-09 joint
connector (CAN2).
CAUTION
A digital multimeter should be used. For details
refer to
.
CAUTION
The test wiring harness should be used. For
details refer to
(1) Disconnect the connector, and measure at the
wiring harness side.
CAUTION
When measuring the resistance, disconnect the
negative battery terminal. For details refer to
(2) Ensure that the negative battery terminal is
disconnected.
(3) Resistance between C-09 joint connector (CAN2)
AC310628AY
Connector: C-09 <RHD>
C-09 (GR)
Harness side
AC310183
AF
Connector: C-306 <RHD>
Harness side
AC209364MM
Harness side: C-09
Test
harness
AC310628AY
Connector: C-09 <RHD>
C-09 (GR)
Harness side
AC209364MJ
Harness side: C-09
Test harness
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст