Mitsubishi Grandis. Manual — part 917
36-1
GROUP 36
PARKING BRAKES
CONTENTS
GENERAL INFORMATION . . . . . . . .
SPECIFICATION(S) . . . . . . . . . . . . . .
SERVICE SPECIFICATIONS . . . . . . . . . . .
ON-VEHICLE SERVICE. . . . . . . . . . .
PARKING BRAKE LEVER STROKE CHECK AND
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . .
PARKING BRAKE SWITCH CHECK . . . . .
LINING RUNNING-IN . . . . . . . . . . . . . . . . .
PARKING BRAKE LEVER . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
PARKING BRAKE CABLE. . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
PARKING BRAKE LINING AND DRUM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . . . . . .
GENERAL INFORMATION
PARKING BRAKES
36-2
GENERAL INFORMATION
M1361000100429
The parking brake is of a mechanical rear-wheel
acting type, and its operation utilises a parking brake
lever.
CONSTRUCTION DIAGRAM
SPECIFICATION(S)
SERVICE SPECIFICATIONS
M1361000300508
ON-VEHICLE SERVICE
PARKING BRAKE LEVER STROKE
CHECK AND ADJUSTMENT
M1361000900458
1. Pull the parking brake lever with a force of
approximately 200 N and count the number of
notches.
Standard value: 3
− 5 notches
2. If the parking brake lever stroke is not the
standard value, adjust as described below.
(1) Remove the floor console panel (Refer to
GROUP 52A, Floor Console Assembly
).
AC211553
AC104333
AC304152
Parking brake lever assembly
Parking brake cable
AB
Drum-in-disc brake
Item
Standard value
Limit
Parking brake lever stroke
3
− 5 notches
−
Rear brake lining thickness mm
2.8
0.8
Rear drum inside diameter mm
190.0
191.0
ON-VEHICLE SERVICE
PARKING BRAKES
36-3
(2) Loosen the adjusting nut to move it to the
cable rod end so that the cable will be free.
(3) Remove the rear brake adjusting hole plug.
Then insert a flat-tipped screwdriver to turn the
adjuster to the arrow direction (to expand the
shoe) until the parking brake shoe makes
contact and the disc can no longer be turned.
Back off the adjuster to the opposite direction
by five notches.
CAUTION
If the parking brake lever stroke is below the
standard value and the braking is too firm, the
rear brakes may drag.
(4) Adjust the parking brake lever stroke to the
standard value by turning the adjusting nut.
After the adjustment, ensure that there is no
free play between the adjusting nut and the
parking brake lever.
(5) After the parking brake lever stroke is
adjusted, raise the rear of the vehicle. Release
the parking brake, turn the rear wheels to
confirm that the rear brakes are not dragging.
PARKING BRAKE SWITCH CHECK
M1361003300499
1. Remove the floor console panel. (Refer to
GROUP 52A, Floor Console Assembly
).
2. Check for continuity between the parking brake
switch terminal and the switch mounting bolt.
LINING RUNNING-IN
M1361001100347
CAUTION
Carry out running-in in a place with good
visibility, and pay careful attention to safety.
Carry out running-in by the following procedure when
replacing the rear brake disc rotors, or when brake
performance is insufficient.
1. Adjust the parking brake lever stroke to the
specified value.
Specified value (Operation force: Approx.
200 N): 3
− 5 notches
2. Hook a spring balance onto the centre of the
parking brake lever grip and pull it with a force of
100
− 150 N in a direction perpendicular to the
handle.
3. Drive the vehicle at a constant speed of 35
− 50
km/h for 100 metres.
AC311282
Cable rod
Adjusting nut
AB
AC202320AC
Adjuster
When parking brake lever is pulled Less than 2
ohms
When parking brake lever is
released
Open circuit
AC312896AB
PARKING BRAKE LEVER
PARKING BRAKES
36-4
4. Release the parking brake and let the brakes cool
for 5
− 10 minutes.
5. Repeat the procedure in steps 2 to 4 four or five
times.
PARKING BRAKE LEVER
REMOVAL AND INSTALLATION
M1361001300437
Pre-removal Operation
Rear Floor Console Assembly Removal (Refer to GROUP
52A, Floor Console
Post-installation Operation
• Parking Brake Lever Stroke Adjustment (Refer to
• Rear Floor Console Assembly Installation (Refer to
GROUP 52A, Floor Console Assembly
AC313265
AB
3
4
5
Section A - A
A
A
B
B
Section B - B
1
2
Removal steps
1.
Adjusting nut
2.
Parking brake switch connector
3.
Parking brake cable connection
4.
Parking brake lever assembly
5.
Parking brake switch
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст