Mitsubishi Grandis. Manual — part 922
TROUBLESHOOTING
TRACTION CONTROL/ACTIVE STABILITY CONTROL SYSTEM
35C-13
sensor circuit and body earth.
OK: No continuity
• Code No.C1200 is set: Between signal
terminal 33 and body earth, and between
earth terminal 34 and body earth
• Code No.C1205 is set: Between signal
terminal 45 and body earth, and between
earth terminal 46 and body earth
• Code No.C1210 is set: Between signal
terminal 42 and body earth, and between
earth terminal 43 and body earth
• Code No.C1215 is set: Between signal
terminal 36 and body earth, and between
earth terminal 37 and body earth
Q: Is the check result normal?
YES :
Go to Step 14.
NO (Continuity exists between terminal 33 or
terminal 34 and body earth) :
Go to Step 6.
NO (Continuity exists between terminal 45 or
terminal 46 and body earth) :
Go to Step 8.
NO (Continuity exists between terminal 42 or
terminal 43 and body earth) :
Go to Step 10.
NO (Continuity exists between terminal 36 or
terminal 37 and body earth) :
Go to Step 12.
STEP 6. Check TCL/ASC-ECU connector A-04
and wheel speed sensor <front: RH> connector
A-02 for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
Q: Is the check result normal?
YES :
Go to Step 7.
NO :
Repair or replace the damaged
component(s). Then go to Step 16.
AC312621
Oil reservoir
Connector: A-04
AB
A-04
Hydraulic unit
(with built-in TCL/ASC-ECU)
A-04 Harness connector
(harness side)
AC312616AB
Connector: A-02
A-02 (GR)
A-02 Harness
connector
(harness side)
TROUBLESHOOTING
TRACTION CONTROL/ACTIVE STABILITY CONTROL SYSTEM
35C-14
STEP 7. Check the harness wires between
TCL/ASC-ECU connector A-04 (terminal 33, 34)
and wheel speed sensor <front: RH> connector
A-02 (terminal 2, 1).
Q: Is the check result normal?
YES :
Go to Step 14.
NO :
Repair the wiring harness. Then go to Step
16.
STEP 8. Check TCL/ASC-ECU connector A-04
and wheel speed sensor <front: LH> connector
A-05 for loose, corroded or damaged terminals,
or terminals pushed back in the connector.
Q: Is the check result normal?
YES :
Go to Step 9.
NO :
Repair or replace the damaged
component(s). Then go to Step 16.
AC312621
Oil reservoir
Connector: A-04
AB
A-04
Hydraulic unit
(with built-in TCL/ASC-ECU)
A-04 Harness connector
(harness side)
AC312616AB
Connector: A-02
A-02 (GR)
A-02 Harness
connector
(harness side)
AC312621
Oil reservoir
Connector: A-04
AB
A-04
Hydraulic unit
(with built-in TCL/ASC-ECU)
A-04 Harness connector
(harness side)
AC312617AB
Connector: A-05 <L.H.drive vehicles>
A-05 (GR)
A-05 Harness
connector
(harness side)
AC312619AB
Connector: A-05 <R.H.drive vehicles>
A-05 (GR)
A-05 Harness
connector
(harness side)
TROUBLESHOOTING
TRACTION CONTROL/ACTIVE STABILITY CONTROL SYSTEM
35C-15
STEP 9. Check the harness wires between
TCL/ASC-ECU connector A-04 (terminal 45, 46)
and wheel speed sensor <front: LH> connector
A-05 (terminal 1, 2).
Q: Is the check result normal?
YES :
Go to Step 14.
NO :
Repair the wiring harness. Then go to Step
16.
AC312621
Oil reservoir
Connector: A-04
AB
A-04
Hydraulic unit
(with built-in TCL/ASC-ECU)
A-04 Harness connector
(harness side)
AC312617AB
Connector: A-05 <L.H.drive vehicles>
A-05 (GR)
A-05 Harness
connector
(harness side)
AC312619AB
Connector: A-05 <R.H.drive vehicles>
A-05 (GR)
A-05 Harness
connector
(harness side)
TROUBLESHOOTING
TRACTION CONTROL/ACTIVE STABILITY CONTROL SYSTEM
35C-16
STEP 10. Check TCL/ASC-ECU connector A-04,
intermediate connector C-16, C-124, D-28 and
wheel speed sensor <rear: RH> connector D-06
for loose, corroded or damaged terminals, or
terminals pushed back in the connector.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст