Mitsubishi Grandis. Manual — part 832
TRANSMISSION CONTROL
MANUAL TRANSMISSION (FF)
22A-9
CAUTION
Insert thoroughly the gearshift link clip, shift
cable and select cable until they click in place.
3. After installing the new gearshift link clip to the
cable bracket of the transmission, install the shift
cable and select cable to the cable bracket.
NOTE: The clip is reversible.
4. Move the shift lever to all positions and check that
the operation is smooth.
>>B<< GEARSHIFT CABLE CLIP
INSTALLATION
1. Make sure that there is no excessive play at the
shift cable end gearshift cable clip. If there is
excessive play or the gearshift cable clip is
disengaged from the shift cable end, check the
clip opening gap. If the gap is more than 9.5 mm,
squeeze the gearshift cable clip until the relaxed
gap reaches 5 to 8 mm.
2. Engage the gearshift cable clip with the shift cable
hook securely, and push the gearshift cable clip
with your thumbs until it clicks in place.
3. Install the shift cable to the shift lever.
AC210558
Shift cable, Select cable
New gearshift
link clip
Cable bracket
AB
AC210559 AB
9.5 mm
5 - 8 mm
AC210560 AB
TRANSMISSION CONTROL
MANUAL TRANSMISSION (FF)
22A-10
SHIFT LEVER ASSEMBLY
DISASSEMBLY AND REASSEMBLY
M1221004000218
AC311632
1
2
3
AB
12 ± 2 N·m
Disassembly steps
1.
Gearshift control lever assembly
2.
Gearshift link bushing
3.
Gearshift link bracket
Disassembly steps (Continued)
TRANSMISSION ASSEMBLY
MANUAL TRANSMISSION (FF)
22A-11
TRANSMISSION ASSEMBLY
REMOVAL AND INSTALLATION
M1221002700330
CAUTION
*: Indicates parts which should be temporarily tightened, and then fully tightened after installing the
engine into the vehicle.
Pre-removal and Post-installation Operation
• Air Cleaner assembly, Air Cleaner Bracket Removal and
Installation (Refer to GROUP 15, Air Cleaner
).
• Battery and Battery Tray Removal and Installation.
• Transmission Oil Draining and Refilling (Refer to
).
• Under Cover Removal and Installation (Refer to GROUP
51, Front Bumper
). <LHD>
• Drive Shaft Removal and Installation (Refer to GROUP 26
• Stator Motor Assembly Removal and Installation (Refer to
GROUP 16, Stator Motor Assembly
AC310807AC
1
3
8
48 ± 5 N·m
6
6
7
18 ± 3 N·m
9
2
48 ± 5 N·m
18 ± 3 N·m
4
18 ± 3 N·m
8
18 ± 3 N·m
5
5
1
Removal steps
1.
Transmission harness clamp
2.
Back-up lamp switch connector
connection
3.
Vehicle speed sensor harness
connector connection
4.
Clutch release cylinder and clutch
oil pipe
5.
Clip
6.
Snap pin
7.
Cable bracket and cable assembly
<Transmission side>
>>B<<
8.
Transmission assembly upper part
coupling bolts
9.
Harness clamp bracket
Removal steps (Continued)
TRANSMISSION ASSEMBLY
MANUAL TRANSMISSION (FF)
22A-12
REMOVAL SERVICE POINTS
<<A>> ENGINE AND TRANSMISSION
ASSEMBLY
SUPPORTING/TRANSMISSION
MOUNTING BRACKET ASSEMBLY
REMOVAL
AC310808
18
19
18
17
83 ± 12 N·m*
22
57 ± 7 N·m*
15
11
26 ± 5 N·m
9.0 ± 1.0 N·m
57 ± 7 N·m*
90 ± 10 N·m
49 ± 9 N·m
49 ± 9 N·m
13
AB
20
48 ± 5 N·m
48 ± 5 N·m
10
12
14
83 ± 12 N·m*
16
N
N
22 ± 4 N·m
21
N
Removal steps
•
Front exhaust pipe, Catalytic
converter connection (Refer to
GROUP 15, Exhaust pipe and
main muffler
).
10. Transmission stay
11. Flywheel housing front lower
cover
12. Self locking nut
13. Centremember assembly
14. Self locking nut
15. Rear roll mount bracket
<<A>>
•
Engine and transmission
assembly supporting
16. Self locking nut
<<A>>
17. Transmission mounting bracket
assembly
>>A<<
18. Transmission mounting stopper
19. Transmission mounting body side
bracket
<<B>>
•
Engine assembly supporting
20. Transmission assembly lower part
coupling bolts
21. Vehicle speed sensor sub harness
22. Transmission assembly
Removal steps (Continued)
AC210384
Garage jack
Engine and transmission assembly
AB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст