Mitsubishi Grandis. Manual — part 231
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-386
Normal conditions are displayed for all the items. :
Go to Step 3.
Normal condition is not displayed for item No.03 :
Refer to inspection procedure Q-11 "The
key reminder switch signal is not received
Normal condition is not displayed for item No.05,
07, 41 or 42 :
Refer to inspection procedure Q-14
"All the door switch signals are not received
Normal condition is not displayed for item No.21
and 22 :
Refer to inspection procedure Q-15 "The
driver's door lock actuator switch signal is
not received <LH drive vehicles>
Normal condition is not displayed for item No.31 or
32 :
Refer to inspection procedure Q-22 "The
interior lamp "all on" or "all off" switch signal
is not sent to the ETACS-ECU
Step 3. Retest the system.
Check that the right or left room lamp illuminates
when the interior lamp switch is operated.
Q: Is the check result normal?
YES :
Go to Step 6.
NO :
Go to Step 4.
Step 4. Connector check: C-219 ETACS-ECU
connector, E-02 room lamp connector
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Repair the defective connector.
AC310626
Connector: C-219
Junction block (Rear view)
<LHD>
AB
Junction block side
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
AC310651
AD
Connector: E-02 <LHD>
Harness side
AC310655
AE
Connector: E-02 <RHD>
Harness side
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-387
Step 5. Check the wiring harness from C-219
ETACS-ECU connector terminal No.6 to E-02
room lamp connector terminal No.10.
NOTE:
Prior to the wiring harness inspection, check
intermediate connector E-11 and junction block
connector C-211, and repair if necessary.
• Check the power supply line for open circuit.
Q: Is the check result normal?
YES :
Replace the room lamp.
NO :
Repair the wiring harness.
Step 6. Check the room lamp switch.
Check which position (ON or DOOR) of the room
lamp switch does not activate the room lamp.
Q: Which switch position does not activate the lamp?
The lamp illuminates at neither the ON nor DOOR
position. :
Go to Step 7.
The lamp does not illuminate at the ON position. :
Go to Step 7.
The lamp does not illuminate at the DOOR position.
:
Go to Step 9.
AC310626
Connector: C-219
Junction block (Rear view)
<LHD>
AB
Junction block side
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
AC310651
AD
Connector: E-02 <LHD>
Harness side
AC310655
AE
Connector: E-02 <RHD>
Harness side
AC310623
AC310623
Connector: C-211
AQ
<LHD>
Junction block (Front view)
Harness side
3
1
2
AC310618
AC310618
Connector: C-211 <RHD>
AS
Harness side
Junction block (Front view)
3
1
2
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-388
Step 7. Connector check: E-02 room lamp
connector
Q: Is the check result normal?
YES :
Go to Step 8.
NO :
Repair the defective connector.
Step 8. Check the bulbs of the room lamp.
Check that the room lamp bulbs are not burned out.
Q: Is the check result normal?
YES :
Replace the room lamp.
NO :
Replace the room lamp bulb.
Step 9. Connector check: E-02 room lamp
connector
Q: Is the check result normal?
YES :
Go to Step 10.
NO :
Repair the defective connector.
Step 10. Check the bulbs of the room lamp.
Check that the room lamp bulbs are not burned out.
Q: Is the check result normal?
YES :
Go to Step 11.
NO :
Replace the room lamp bulb.
AC310651
AD
Connector: E-02 <LHD>
Harness side
AC310655
AE
Connector: E-02 <RHD>
Harness side
AC310651
AD
Connector: E-02 <LHD>
Harness side
AC310655
AE
Connector: E-02 <RHD>
Harness side
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) USING SWS MONITOR
54C-389
Step 11. Connector check: C-219 ETACS-ECU
connector
Q: Is the check result normal?
YES :
Go to Step 12.
NO :
Repair the defective connector.
AC310626
Connector: C-219
Junction block (Rear view)
<LHD>
AB
Junction block side
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст