Mitsubishi Grandis. Manual — part 59
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-233
Step 8. Check the wiring harness between C-219
ETACS-ECU connector terminal No.16 and G-05
rear wiper motor connector terminal No.3.
NOTE:
Prior to the wiring harness inspection, check
intermediate connector G-14 and junction block
connectors C-210, and repair if necessary.
• Check the output line.
Q: 1Is the check result normal?
YES :
Go to Step 9.
NO :
Repair the wiring harness.
Step 9. Retest the system.
Check that the rear wiper works normally.
Q: Is the check result normal?
YES :
The trouble can be an intermittent
malfunction (Refer to GROUP 00
− How to
Cope with Intermittent Malfunction
NO :
Replace the ETACS-ECU.
AC310626AD
Connector: C-219 <LHD>
Junction block (Rear view)
Junction block side
AC310620
Connector: C-219
Junction block
(Rear view)
<RHD>
AB
Junction block side
AC310222
Connector: G-05
AH
Harness side
AC310623
Connector: C-210
AN
<LHD>
Junction block (Front view)
Harness side
AC310618
Connector: C-210 <RHD>
AO
Junction block (Front view)
Harness side
AC310222
Connector: G-14
AF
2
1
4
3
13
8
11
10
5
7
12
6
14
9
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-234
Inspection Procedure H-2: The rear wiper does not stop at the specified park position.
CAUTION
Whenever the ECU is replaced, ensure that the
input and output signal circuits are normal.
COMMENTS ON TROUBLE SYMPTOM
If the rear wiper does not stop normally within the
predetermined range, the rear wiper motor or the
ETACS-ECU may be defective.
POSSIBLE CAUSES
• Malfunction of the rear wiper motor
• Malfunction of the ETACS-ECU
• Damaged harness wires and connectors
IGNITION
SWITCH (ACC)
REAR
WIPER
RELAY
REAR WIPER
MOTOR
ETACS-
ECU
J/B SIDE
Wire colour code
B : Black LG : Light green G : Green L : Blue W : White Y : Yellow SB : Sky blue
BR : Brown O : Orange GR : Gray R : Red P : Pink V : Violet
Rear Wiper Auto-stop Signal Input
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-235
Step 1. Connector check: G-05 rear wiper motor
connector
Q: Is the check result normal?
YES :
Go to Step 2.
NO :
Repair the connector.
Step 2. Check the rear wiper motor.
Refer to GROUP 51
− Rear wiper and washer
Q: Is the check result normal?
YES :
Go to Step 3.
NO :
Replace the rear wiper motor.
Step 3. Voltage measurement at the G-05 rear
wiper motor connector.
(1) Disconnect the connector, and measure at the
wiring harness side.
(2) Ignition switch: ACC
(3) Check the voltage between G-05 rear wiper
motor connector terminal No.1 and body earth
OK: System voltage
Q: Is the check result normal?
YES :
Go to Step 5.
NO :
Go to Step 4.
AC310222
Connector: G-05
AH
Harness side
AC310222
Connector: G-05
AH
Harness side
AC310507 EL
Connector G-05
(Harness side)
SYMPTOM PROCEDURES
SMART WIRING SYSTEM (SWS) NOT USING SWS MONITOR
54B-236
Step 4. Check the wiring harness between
ignition switch (ACC) and G-05 rear wiper motor
connector terminal No.1.
NOTE:
AC310222
Connector: G-05
AH
Harness side
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст