Mitsubishi Grandis. Manual — part 610
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54D-538
terminal No.5.
OK: 2
Ω or less
(5) Continuity between C-37 jumper connector
terminal No.3 and C-07 centre display connector
terminal No.15.
OK: 2
Ω or less
CAUTION
Strictly observe the specified wiring harness
repair procedure. For details refer to
Q: Are the check results normal?
YES :
<All the resistances measure 2 TAG or
less> Power supply to the centre display
may be suspected. Diagnose the centre
display system. Refer to
NO :
<Either or all of the resistances measure
more than 2
Ω> Repair the wiring harness
between the centre display connector and
the jumper connector.
STEP 19. Connector check: C-119 SRS-ECU
connector
CAUTION
The strand end of the twist wire should be within
10 cm from the connector. For details refer to
Q: Is the check result normal?
YES :
Go to Step 20 .
NO :
Repair the defective connector.
STEP 20. MUT-III CAN bus diagnostics (C-119
SRS-ECU connector disconnected)
(1) Disconnect the SRS-ECU connector, and
diagnose by using the MUT-III.
(2) Check that the MUT-III indications correspond to
the illustration.
Q: Is the check result normal?
AC312553
Harness side: C-07
Test
harness
Test
harness
Harness side: C-37
BN
AC310631AZ
Connector: C-119 <RHD>
Harness side
C-119 (Y)
48
37
26
42
31
45
34
47
36
46
35
44
33
43
32
25 24
39
28
41
30
40
29
38
27
23
21
22
A
B
AC310631AZ
Connector: C-119 <RHD>
Harness side
C-119 (Y)
48
37
26
42
31
45
34
47
36
46
35
44
33
43
32
25 24
39
28
41
30
40
29
38
27
23
21
22
A
B
AC309834
MUT
J/C (2)
METER
ETAC S
J/C (1)
ASC -ECU
ENG/AT-ECU
A/C -ECU
SRS-ECU
STR. A .
SNSR
C. DISPL AY
AM
: Red section
on screen
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54D-539
YES :
<MUT-III indications correspond to the
illustration> Go to Step 21 .
NO :
<MUT-III indications do not correspond to
the illustration> Go to Step 22 .
STEP 21. Resistance measurement at C-09 joint
connector (CAN2) and C-119 SRS-ECU
connector.
CAUTION
A digital multimeter should be used. For details
refer to
CAUTION
The test wiring harness should be used. For
details refer to
(1) Disconnect the joint connector (CAN2) and the
SRS-ECU connector, and measure at the wiring
harness side.
(2) Ignition switch: OFF (LOCK)
CAUTION
When measuring the resistance, disconnect the
negative battery terminal. For details refer to
(3) Ensure that the negative battery terminal is
disconnected.
(4) Continuity between C-09 joint connector (CAN2)
terminal No.4 and C-119 SRS-ECU connector
terminal No.32
OK: 2
Ω or less
(5) Continuity between C-09 joint connector (CAN2)
terminal No.15 and C-119 SRS-ECU connector
AC310628AY
Connector: C-09 <RHD>
C-09 (GR)
Harness side
AC310631AZ
Connector: C-119 <RHD>
Harness side
C-119 (Y)
48
37
26
42
31
45
34
47
36
46
35
44
33
43
32
25 24
39
28
41
30
40
29
38
27
23
21
22
A
B
AC312553
Harness side: C-09
Test
harness
Harness side: C-119
Test
harness
BP
AC312553 BQ
Test
harness
Harness side: C-09
Test
harness
Harness side: C-119
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54D-540
terminal No.43
OK: 2
Ω or less
CAUTION
Strictly observe the specified wiring harness
repair procedure. For details refer to
Q: Are the check results normal?
YES :
<All the resistances measure 2
Ω or less>
Power supply to the SRS-ECU may be
suspected. Diagnose the SRS system.
Refer to
NO :
<Either or all of the resistances measure
more than 2
Ω> Repair the wiring harness
between the joint connector (CAN2) and the
SRS-ECU connector.
STEP 22. Connector check: C-306 steering wheel
angle sensor connector
CAUTION
The strand end of the twist wire should be within
10 cm from the connector. For details refer to
Q: Is the check result normal?
YES :
Go to Step 23 .
NO :
Repair the defective connector.
STEP 23. MUT-III CAN bus diagnostics (C-119
steering wheel angle sensor connector
disconnected)
(1) Disconnect the steering wheel angle sensor
connector, and diagnose by using the MUT-III.
(2) Check that the MUT-III indications correspond to
the illustration.
Q: Is the check result normal?
YES :
<MUT-III indications correspond to the
illustration> Go to Step 24 .
NO :
<MUT-III indications do not correspond to
the illustration> Go to Step 34 .
STEP 24. Resistance measurement at C-09 joint
connector (CAN2) and C-306 steering wheel
angle sensor connector.
CAUTION
A digital multimeter should be used. For details
refer to
.
CAUTION
The test wiring harness should be used. For
details refer to
(1) Disconnect the joint connector (CAN2) and the
steering wheel angle sensor connector, and
measure at the wiring harness side.
AC310183
AF
Connector: C-306 <RHD>
Harness side
AC310631AZ
Connector: C-119 <RHD>
Harness side
C-119 (Y)
48
37
26
42
31
45
34
47
36
46
35
44
33
43
32
25 24
39
28
41
30
40
29
38
27
23
21
22
A
B
AC309834
MUT
J/C (2)
METER
ETAC S
J/C (1)
ASC -ECU
ENG/AT-ECU
A/C -ECU
SRS-ECU
STR. A .
SNSR
C. DISPL AY
AN
: Red section
on screen
AC310628AY
Connector: C-09 <RHD>
C-09 (GR)
Harness side
AC310183
AF
Connector: C-306 <RHD>
Harness side
DIAGNOSIS
CONTROLLER AREA NETWORK (CAN)
54D-541
(2) Ignition switch: OFF (LOCK)
CAUTION
When measuring the resistance, disconnect the
negative battery terminal. For details refer to
(3) Ensure that the negative battery terminal is
disconnected.
(4) Continuity between C-09 joint connector (CAN2)
terminal No.3 and C-306 steering wheel angle
sensor connector terminal No.3
OK: 2
Ω or less
(5) Continuity between C-09 joint connector (CAN2)
terminal No.14 and C-306 steering wheel angle
sensor connector terminal No.4
OK: 2
Ω or less
CAUTION
Strictly observe the specified wiring harness
repair procedure. For details refer to
Q: Are the check results normal?
YES :
<All the resistances measure 2
Ω or less>
Power supply to the steering wheel angle
sensor may be suspected. Diagnose the
ASC system. Refer to
NO :
<Either or all of the resistances measure
more than 2
Ω> Repair the wiring harness
between the joint connector (CAN2) and the
steering wheel angle sensor connector.
AC204582
Harness side: C-09
EH
Harness side: C-306
Test
harness
Test
harness
AC204582
Harness side: C-09
EG
Harness side: C-306
Test
harness
Test
harness
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст