Mitsubishi Grandis. Manual — part 1045
SIDE AND CURTAIN AIR BAG MODULE(S)
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-232
<CURTAIN AIR BAG MODULE>
REMOVAL SERVICE POINTS
<<A>>NEGATIVE BATTERY CABLE
DISCONNECTION
DANGER
Wait at least 60 seconds after disconnecting
the battery cable before doing any further
work (Refer to
WARNING
Battery posts, terminals and related
accessories contain lead and lead
compounds. WASH HANDS AFTER
HANDLING.
Pre-removal Operation
• Turn the ignition switch to the "LOCK" (OFF) position.
AC313518
AC313454
2
3
4
1
AB
Curtain air bag module removal
steps
<<A>>
1. Negative battery cable connection
•
Headlining (Refer to GROUP 52A,
Headlining
<<C>>
2. Connector
<<D>>
3. Curtain air bag module
4. Strap guide bracket
Curtain air bag module installation
steps
>>A<<
•
Pre-installation inspection
4. Strap guide bracket
>>B<<
3. Curtain air bag module
>>C<<
2. Connector
•
Headlining (Refer to GROUP 52A,
Headlining
1. Negative battery cable connection
>>D<<
•
Post-installation inspection
ACX00583
Insulating tape
Battery
Battery cable (–)
AC
SIDE AND CURTAIN AIR BAG MODULE(S)
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-233
Disconnect the negative battery cable from the
battery and tape the terminal to prevent accidental
connection and air bag(s) deployment.
<<B>> FRONT SEAT ASSEMBLY
REMOVAL
WARNING
Dispose of air bag modules only according
to the specified procedure (Refer to
Refer to GROUP52A, Front seat assembly
<<C>>CONNECTOR REMOVAL
Use a flat-tipped screwdriver to pull out forward and
unlock the locking button of the curtain air bag
harness-side connector.
<<D>>CURTAIN AIR BAG MODULE
REMOVAL
CAUTION
• Never use an electric tester to diagnose the
air bag module circuit. Never attempt to
disassemble the air bag module.
• The removed air bag module should be stored
in a clean, dry place.
INSTALLATION SERVICE POINTS
>>A<< NEGATIVE BATTERY CABLE
DISCONNECTION
DANGER
Wait at least 60 seconds after disconnecting
the battery cable before doing any further
work. (Refer to
WARNING
Battery posts, terminals and related
accessories contain lead and lead
compounds. WASH HANDS AFTER
HANDLING.
Disconnect the negative battery cable from the
battery and tape the terminal to prevent accidental
connection and air bag(s) deployment.
>>B<< CURTAIN AIR BAG MODULE
INSTALLATION
CAUTION
•
Take care not to contort the curtain air bag when
installing it.
• Take care that the surrounding components
do not trap the air bag.
• Take care that the front pillar trim clips or
other do not trap the strap.
Hang the strap on the strap guide.
AC302577AC
Flat-tip screw
driver
Locking button
Harness side
connector
Curtain air bag
module
ACX00583
Insulating tape
Battery
Battery cable (–)
AC
AC313453AB
Strap guide
Strap
SIDE AND CURTAIN AIR BAG MODULE(S)
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-234
>>C<< CONNECTOR INSTALLATION
CAUTION
Connect the connector to the inflator thoroughly.
>>D<< POST-INSTALLATION
INSPECTION
1. Reconnect the negative (
−) battery cable.
2. Turn the ignition switch to “ON” position.
3. Does the SRS warning lamp illuminate for about 7
seconds, and go out?
4. If yes, the SRS system is functioning properly. If
no, refer to
INSPECTION
M1524014900030
FRONT SEAT ASSEMBLY WITH
SIDE-AIRBAG MODULE CHECK
WARNING
•
If any improper part is found during the
following inspection, replace the front
seatback assembly with a new one.
Dispose of the old one according to the
specified procedure (Refer to
•
Never attempt to measure the circuit
resistance of the air bag module (squib)
even if you are using the specified tester.
If the circuit resistance is measured with a
tester, accidental air bag deployment will
result in serious personal injury.
1. Check the air bag module deployment section for
dents or deformation.
2. Check connector for damage, terminals for
deformation, and harness for binds.
AC312486
SRS warning lamp
AB
AC303516
AD
Side-airbag module
deployment section
SIDE AND CURTAIN AIR BAG MODULE(S)
SUPPLEMENTAL RESTRAINT SYSTEM (SRS)
52B-235
CURTAIN AIR BAG MODULE CHECK
WARNING
•
If any improper part is found during the
following inspection, replace the curtain
air bag module (squib) assembly with a
new one. Dispose of the old one
according to the specified procedure
(Refer to
).
•
Never attempt to measure the circuit
resistance of the air bag module (squib)
even if you are using the specified tester.
If the circuit resistance is measured with a
tester, accidental air bag deployment will
result in serious personal injury.
1. Check that the curtain air bag deployment part of
the headlining is normal.
2. Check the inflator surface for cracks, dents or
deformations.
3. Check the air bag for breakage.
4. Check the connector for damage, the terminal for
deformation and the harness for binding.
AC302258AC
Inflator
Curtain air bag module
deployment section
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст