Mitsubishi Grandis. Manual — part 637
CRANKSHAFT OIL SEAL
ENGINE MECHANICAL
11A-25
REMOVAL SERVICE POINTS
<<A>> TRANSMISSION ASSEMBLY
REMOVAL
CAUTION
Do not remove the flywheel bolt shown by the
arrow. If this bolt is removed, the flywheel
assembly will become out of balance and
damaged.
Refer to GROUP 22A, Transmission Assembly
.
<<B>> FLYWHEEL BOLTS/A/T DRIVE
PLATE BOLTS REMOVAL
1. Use special tool flywheel stopper (MD998781) to
secure the flywheel assembly or A/T drive plate.
2. Remove the flywheel bolts or A/T drive plate bolts.
INSTALLATION SERVICE POINTS
>>A<< CRANKSHAFT REAR OIL SEAL
INSTALLATION
1. Apply a small amount of engine oil to the entire
inner diameter of the oil seal lip.
2. Use the following special tools to press-fit the oil
seal.
• Installer bar (MB990938)
• Crankshaft rear oil seal installer (MD998776)
>>B<< FLYWHEEL BOLTS/A/T DRIVE
PLATE BOLTS INSTALLATION
1. Use special tool flywheel stopper (MD998781) to
secure the flywheel assembly or A/T drive plate in
the same manner as removal.
2. Tighten the flywheel bolts or A/T drive plate bolts
to the specified torque.
Tightening torque: 132
± 5 N⋅m
AC300897
AC308604
Flywheel
bolt
Engine front
AB
Flywheel
assembly
AC301854AB
MD998781
AC102328 AB
Oil seal
MB990938
MD998776
Crankshaft
(Engine oil)
AC301855AB
MD998781
CRANKSHAFT OIL SEAL
ENGINE MECHANICAL
11A-26
>>C<< CRANKSHAFT FRONT OIL SEAL
INSTALLATION
1. Apply a small amount of engine oil to the outer
diameter of special tool crankshaft front oil seal
guide (MD998285) and install it to the crankshaft.
2. Apply a small amount of engine oil to the entire
inner diameter of the oil seal lip.
3. Use special tool crankshaft front oil seal installer
(MD998375) to press-fit the oil seal.
>>D<< CRANKSHAFT BALANCER SHAFT
DRIVE SPROCKET INSTALLATION
1. Clean or degrease the front case, the crankshaft
and the crankshaft balancer shaft drive sprocket
as shown.
NOTE: Also clean the degreased surfaces.
2. Install the crankshaft balancer shaft drive sprocket
in the direction shown in the illustration.
AC102329AC
MD998285
(Engine oil)
(Oil applied to the
circumference)
Oil seal
Crankshaft
MD998375
AC301346
AB
: Clean
: Clean and degrease
Crankshaft
balancershaft
drive sprocket
Engine front
Front case
Crankshaft
CYLINDER HEAD GASKET
ENGINE MECHANICAL
11A-27
CYLINDER HEAD GASKET
REMOVAL AND INSTALLATION
M1112004001034
Pre-removal Operation
• Fuel Line Pressure Reduction [Refer to GROUP 13A,
On-vehicle Service
− Fuel Pump Relay Disconnection
(How to Reduce Pressurized Fuel Lines)
• Engine Coolant Draining (Refer to GROUP 14, On-vehicle
Service
− Engine Coolant Replacement
• Cowl Top Panel Removal (Refer to GROUP 42, Loose
Panel
• Engine Cover Removal (Refer to
• Air Cleaner Removal (Refer to GROUP 15, Air Cleaner
).
Post-installation Operation
• Air Cleaner Installation (Refer to GROUP 15, Air Cleaner
).
• Engine Cover Installation (Refer to
• Cowl Top Panel Installation (Refer to GROUP 42, Loose
Panel
• Engine Coolant Refilling (Refer to GROUP 14, On-vehicle
Service
− Engine Coolant Replacement
).
• Fuel Leak Check
AC312959AB
AC312959
1
5.0 ± 1.0 N·m
14 ± 3 N·m
10
9
8
7
6
5
4
3
2
N
N
(Engine)
(Transmission fluid)
13 ± 1 N·m
11 ± 1 N·m
11 ± 1 N·m
11 ± 1 N·m
11 ± 1 N·m
Removal steps
1.
Control wiring harness connection
2.
Battery wiring harness connection
3.
Breather hose, transmission fluid
level gauge & guide assembly
4.
O-ring
5.
Radiator lower hose clamp
6.
Transmission fluid level gauge
bracket
7.
Canister vacuum hose connection
8.
Brake booster vacuum hose
connection
Removal steps (Continued)
CYLINDER HEAD GASKET
ENGINE MECHANICAL
11A-28
9.
Engine oil level gauge and guide
assembly
10. O-ring
Removal steps (Continued)
AC312963
AC312963
(Engine oil)
AB
18
17
16
15
14
13
12
11
22
21
19
20
N
<Cold engine>
78 ± 2 N·m
φ 0 N·m φ 20 ± 2 N·m
φ +90˚φ +90˚
11 ± 1 N·m
31 ± 3 N·m
31 ± 3 N·m
89 ± 9 N·m
N
(Engine oil)
Removal steps
11. Detonation sensor connection
12. Battery wiring harness connection
13. Inlet manifold stay
•
Exhaust manifold (Refer to GROUP
15, Exhaust Manifold
•
Timing belt upper cover (Refer to
<<A>>
>>E<<
14. Camshaft sprocket
<<B>>
>>D<<
15. Radiator upper hose connection
<<B>>
>>D<<
16. Hose clip
17. Water hose connection
•
Water inlet fitting and thermostat
case assembly (Refer to GROUP
14, Water Hose and Water Pipe
18. Fuel return hose connection
<<C>>
>>C<<
19. Fuel high-pressure hose
connection
•
Rocker cover assembly (Refer to
<<D>>
>>B<<
20. Cylinder head bolts
21. Cylinder head assembly
>>A<<
22. Cylinder head gasket
Removal steps (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст